I'm currently using the High Artisan 4 pill stem for my TM2 using temperature setting 8 and I'm impressed with it. I ended up flooding my lungs with vapor on my first hit using it due to the wide open airflow that I wasn't use to with the stock CU. The stock CU, considering it's small size, is very efficient at cooling but gunks up way too quickly for me to be considered acceptable. These pill stems alleviate this issue and it still feels very portable to me when comparing it to jhooks or extra long stems. The stem can fit perfectly into a round plastic joint tube for traveling. The wooden mouthpieces that fit the pill stems aren't really neccessary unless you plan on sharing your TM and hitting it back to back together. The cooling effect and flavor is also better (less stainless steel in airpath). The v2 dosing capsules fit it perfectly, sitting flush with the end of the stem, you don't need to use any basket screens when using the capsules. Or you can use a rimless or rimmed basket screen. I prefer the rimmed basket screen as I never have to adjust it with picking tools after emptying a bowl like with the rimless baskets which tend to slide around inside the stem. The rim part of the rimmed basket screens are slightly smaller in diameter compared to the stem so the rim doesn't catch the o-ring when pulling the stem out from the TM. For about $30-40, just get it. It's my daily driver and I will never go back to using the stock CU again.
TinyMight / TM 2
- Thread starter kuzko
- Start date
Pghdrummer93
Member
Opened up the tm2. The contacts on the vibrate bumper are really loose, are they soldered on? Or slipped in? Might have to send it in for repair.
Momor
Well-Known Member
Could you post a picture of it ? When you say the contacts a loose, are not attached at all to the motor ?
Does that motor still look like this ?
If so, you may just have to gently bend those legs a little upward so they make better contact to the electronic board.
Pghdrummer93
Member
I can take pics soon. But the little tabs can be pulled out and held. That's how loose they are.
dman28
Vaping for the health of it.
He sent me a new device bottom with the hepatic motor attached. I can post a picture of the old unit with the disk and motor detached if you wish to see in order to tinker yourself. It was a new 1.5 TM I had issues with. The service and response was excellent.
Pghdrummer93
Member
Yeah man that'd be great! My cousin is an electrical engineer and fixes guitar amps and pedals. Do you think it'd be an easy fix for someone like him? How do you get the prongs more rigid and stable? Mine seem so loose. That's why I wasn't sure if it was soldered on or something lol
farmerpalmersnt
Well-Known Member
Ebonised mine with vinegar and steel wool. Think black looks ace.
DaVapeGuy
Well-Known Member
OOS
vapviking
Old & In the Way
Ebonised mine with vinegar and steel wool. Think black looks ace.
We assume you dis-assembled it?
Are these first TM2's coming through as simply unfinished walnut?
Shrike
Flower Potted, Maxed, & Rio'd.
***POOF*** They're gone...
ArtVandalay422
Well-Known Member
This is probably a stupid question, but is it okay to clean the titanium stem in ISO? Is there any type of coating or anything on the stem that ISO may cause an issue with? I assume not, but am not sure, as I've never had any titanium parts in any of my vapes before.
kilo
Well-Known Member
Not stupid – you are totally safe cleaning the titanium stem in isopropyl alcohol.
enano xl stem filling in until a glass wpa gets here
WisePenny
unknown. unmember.
Nice cat scratch
enano xl stem filling in until a glass wpa gets here
Abele Rizieri Ferrari
Well-Known Member
scooterboy
Muppet, not moped.
Who doesn't believe that? One TM's 4 can be the same temp as another TM's 7. Comparing dial setting numbers between TM's is meaningless.
noobvaperct
Well-Known Member
Anyone here know if you can fit a TRWW mouth piece on a High Artisan terp pill stem? Just want to see what my options are as I prefer TRWW MP's instead of the wooden ones from HA.
I'm freaking itching to buy a stem and mouthpiece but everyone is out!
I'm freaking itching to buy a stem and mouthpiece but everyone is out!
Did you reach out to HA? I bet they will make a custom on demand. GVB also has some ready to go, but he does not make a separate MP, like HA.
Last edited:
noobvaperct
Well-Known Member
I asked the other day and they no longer accept custom orders until they can create a better system to support that.
What's the website for GBV? Also I do like the dimpled stems from TRWW - I would totally get a stem and MP from him if there were some to grab
Abele Rizieri Ferrari
Well-Known Member
Good vibes boro on instagram
TRWW also has TM stems with a rounded end which is pretty comfortable ime. E.g. this which you probably already found
Too bad about the stopping custom orders for HA. Good to know for me though.I asked the other day and they no longer accept custom orders until they can create a better system to support that.
What's the website for GBV? Also I do like the dimpled stems from TRWW - I would totally get a stem and MP from him if there were some to grab
GVB sells via O'Connell Woodworks site. Although I usually just order directly from him on Instagram.
I see TM stems available on TRWW right now? Although the MP is no longer listed.