Recent content by ren.dnb

WOO HOO! I got my Ed's TNT stem in the mail today! Came sooner than I thought it would for a custom job. But, got it, ooo'd and ahh'd at it, loaded her up and took it for a spin. I gotta say, I'm a glass guy and I thought I'd never use anything but glass. But the Ed's TNT stem breaks that for...

Well, slightly disappointed that I haven't heard back from the folks that make The Hammer regarding custom stems. Freaks me out a little bit, makes me wonder if I could get warranty support. Oh well, Might as well buy up another Hammer or 2 just to keep some spares around. Thanks @VAPEHUNTER...

I noticed that too. I had one a couple of years ago, but I broke in due to my own stupidity one night. I wanted to buy a new one, but they are ALWAYS sold out. I've sent them an email asking if they still make custom stems or how to go about getting one. Just thought I'd share this; The Hammer...

Wow very nice! I love what you've done physically to the FW4. Trimming off the tabs makes it look great! And that case is almost too perfect for the device lol. Thanks for sharing, gives me some ideas now lol.

If you have an MFLB... I've found the MFLB little brush is awesome. I use it on everything from my E-nano stem, to my FW4 capsules and mouthpiece. All I do is sweep out the capsule with the MFLB brush, and sweep the bottom of the mouthpiece out. That keeps it clean for quite a while. I'll do an...

I believe this is just the sound of the coil in the heater expanding as it gets hotter. I noticed mine does that too, but only when I vape in a really quiet place. Normally theres too much background noise to hear it.

Ok!! I got my FW4 back! I sent it off last Saturday so Marc could replace the heater unit in the device. Just to recap, I've been having problems with my FW4 heating up too much. It would char my material on every heat setting no matter how hard my draw was. The unit itself would also get...

This is good advice! I used to do this, then I got bad about breaking my time. I would usually wait until 7:30 or 8pm and then I'd load up my e-nano stem and usually that 1 stem was enough for me. Over time I got lazy and ended up just simply breaking the rules. For the past 4 months or so I...

I try to throw in sessions with edibles between vape sessions. Usually a couple of my little brownies keeps me straight for a long time. But I looooove to vape haha! So I completely understand. My useless piece of advice would be edibles with the ABV. Otherwise as suggested above, you'll have...

Looking to get away from battery operated devices for now. VAS is kicking hard on the Lotus! I have a Hammer, but the igniter is finicky. Would rather have something where I just have to replace the lighter if something goes wrong. I'm assuming I can just use standard pipe cleaners to clean the...

Ok.... I'm trying to determine whats going on. The herb that I've been able to get for the last few weeks has been weird. It seems to vape faster and I go through it faster (in all of my vapes not just the FW4). I had to turn down the heat on my desktop as it seemed like it wasn't very heat...

Ok quick question for anyone experienced. Does the FW4 heat more intense the harder you draw? Or is it just me...

Thats what I'm thinking. Since the heater and sensor are basically all in the same unit, if Marc replaces the heater it should work. I can hear the element click on whenever I start drawing and get the buzz. So thats why I've kinda ruled that out. Settings 1 and 2 are about it for me, can't...

Once I get an ebonized one and/or get my current FW4's heater replaced, I'll be able to confirm. Really have a feeling the heater is running hotter than it should. Too bad I can't adjust the heat off set the other way lol.. if it were at -2, it would be perfect.

Yes... I've experimented with all kinds of draws. When I sent it off initially, Marc said it was running hotter than normal, and the recal cooled it off quite a bit. It vaped better on setting 2 for a few days, then it seemed to creep back to getting hotter again but not nearly as hot as when I...