Recent content by Minsc_NBoo

The glass G3 might be worth a look. It's $40 and apparently the flavour is good

I'm using both V1 & V2 at the same depth. I run V2 at 320 to 335c in the auto timeout mode. For the V1 I drop it to 285c, and it gives similar extraction with no hight adjustment Edit - I forgot to say I'm using 3mm rubies in the V2. If you are using zirc 290 to 310c gives me nice extraction. I...

The screen has got 3 little fins that screw in. You need to line them up with the notches on the head, and give it a firm clockwise turn. And make sure the F marker on the screen are the right way up Check the number of balls. If there are too many the screen might not screw in. I think I have...

I'm using 3mm rubies and I'm using timeout method. 320c for native use and 335c on a bong (608f & 635f) This gives me full extraction in one cycle and leaves the AVB a light brown

For removing the V1, i just put my finger in the adaptor and gently press down until it starts moving. Pop the glass out then remove the silicone insert afterwards I like the V2 adaptor. It sits below the wand so the only thing inside the wand is your Tempest! The glass can leech some of the...

It's an upgrade for the cap, so you will still be using the T1 bowl I believe you get an induction sleeve, a whole new indicator housing, VI and click disk.

I don't have any issues with the T1 roast in half bowl or full bowl either. It's mainly the heat retention which is better on the T2. It just means I'll have a more leisurely MTL session I'm also interested in the simplified VI installation. I'm a bit scared to open the V1 in case I mess up...

Yes I am still using my ebony V1. I have for T2 set up with the full bowl & rubies. I swapped the 3 mm zirc balls into the V1, and set it up with the half bowl setting. T1 is for MTL sessions, or when I want a microdose. Good for weeknights T2 is for big DTL and bong hits. This one is used...

Yes they are all 8mm, same as the dynavaps. You could stick the Dynavap B on the Tempest 2 stem if you wanted to for a laugh 😉

I don't find the T1 screen too bad. I roll the screen flat first. The reload is good for this but I've been using one of those little wooden brushes like a mini rolling pin! I'm using the reload screwdriver. I drop the screen in, I do a little anticlockwise twist, and this helps it catch the...

So I have made my first attempt at a video of my Tempest 2 in action. I had trim it down for imgur so I had to cut the big cloud at the end short ☁️ This is using full bowl with flower, 3mm rubies on wand auto mode until time out I don't normally pull the the pull the tempest out as much...

Zirc balls are better for mouth to lung, but I prefer rubies for direct lung and bong usage. You get dense vapour more quickly and they can take a lot of heat so it's hard to combust. I also get a very even roast practically every time I use them

I used the reload screwdriver. I was a bit worried too but you just need to give a firm anticlockwise twist and it will open up. 3mm rubies are so good in the T2, especially for big bong rips 🫠 This was posted by Brenyo

I had 44 3mm Zirconia preinstalled when I got the T2. When I swapped the 3mm rubies I could only fit 42 comfortably. I could probably get 2 more in but I was worried about the ball screen catching All 44 3mm zirc went into my OG Tempest though! It's really nice having 2 different set ups...

I mainly use this setting for DTL. I tend to use the bong most of the time. When I do DTL natively I drop the temp to 320c. I still think it's convection heavy as the AVB gets fully cooked but is not too dark Ive swapped the 3mm Zirc balls into my V1 now, so when I do want a more chilled out...