Recent content by Dabberhashery

I have been enjoying my tempest at half bowl for a while now, but I really did notice a step up in consumption - from 0.5g per day with a Revolve gen 2 and a gold fmj... to 1g per day with the Tempest half bowl... Idk why it took me so long to try a third bowl setting, with the mesh somewhere...

This doesn't look like good news for medical cannabis users who drive in the UK: Police powers at the roadside

The Aurora Pedanios ones are fine, I should have just stuck to those. Electric Honeydew, sourdough and farm gas have all been OK, so there are some good ones. Latest ones I can't deal with are from lot420, black cherry punch was terrible but orange cake was not too bad but I think the bcp was...

Unfortunately, for myself at least, uk medical cannabis leaves much to be desired. I'm prescribed myself through Integro who have been excellent. The trouble for me is the quality of the product available. I had to abandon my current batch due to headaches caused by microseeds. However, in...

These hash worms that come out the holes on the side of the bowl have become my early warning sign that I'm gonna a have to clean it soon... especially when I've only been vaping flower

I think this is going to be a permanent fixture for me, I was concerned that the heat would make the water go bad too quickly. I have researched lots about water-borne germs and it is more of a concern here because the water is heated in the 'danger zone' for germs to grown and then will be...

The one I have is 13cm diameter for the heated pad area, here is a pic with the saml straight fab It does have lots of different settings (three temps each for glass, metal and ceramic) but really it just covers from 55 to 85c in 5c increments.

I just bought a coffee warmer to give this a go, I currently have my least favourite bubbler on it as a test :science: its a fauxbius matrix from dhgate with a big thick base... so far so good, it seems to be warming up the water - it took a while for the heat to filter through the base, but...

I've gone for a stainless steel standard size BCG after deliberating over the last couple of months... the delivery estimate is 6-8 weeks so gonna have to kick back and wait and let someone else do the heavy polishing :clap: it was a case of the shiniest one won out in the end! I did buy a new...

My tempest head lives on a water tool most of the time, but at the same time I wouldnt want to go without the stem to go with it... Its a big part of the 'fun' of the device imo... So much to fiddle with :science: Sweet spot for me will be one on a glass stem for taste, one on the metal stem for...

When I bought a Revolve v2 it came with a white cloth a bit like a glasses cleaning one, it was really nice material. I was using it to wipe the tempest before heating and it went well for a while.... until my tempest started making a clicking noise when heating it in the wand one time. I...

I use some 100% cotton make up remover pads that I bought from amazon. https://amzn.eu/d/1IXiq2J I just wrap a bit of concentrate in a bit of torn off cotton and use just enough to lightly fill the half bowl. 400c until time out is where I am now but can go a little higher, with my current...

I'm currently using the Tempest like this, getting good results using it through a water piece. The half bowl setting is the one for me, I've settled on the direct tube + SCU with the air port open halfway to let the air through the helix and then back up to the direct tube (direct bypass in...

My new female post doesn't fit my shovelhead bowl... So if I want to add any glass using this I'll need to have two shovelheads. Or, I could buy a whole new set of posts for the new shovelhead.

I'm a proud new Tempest owner, I managed to get in on the last drop like a sneaky lurker :D Excellent service from Mad Heaters, it was just as flawless as when I ordered my revolve v2... Next day delivery, perfectly packaged and helpful instructions... thanks for the great experience - I always...