TinyMight / TM 2

dzoinp

Well-Known Member
Accessory Maker
The session mode is the same as have the switch always pressed down in the on demand mode... It's a waste of battery...
it has so much power that it almost immediately heats up ..

EDIT:
If possible I would change the session mode for a boost in on demand mode ... does anyone else agree?
 
Last edited:

YaMon

Vaping since 2010
If possible I would change the session mode for a boost in on demand mode ... does anyone else agree?
How do you know it is not already boosting output when you initially press the button? Or are you thinking a way to boost power to finish a bowl without turning the temperature up? I’m running at 6 until the vapor gets whispy and then go to 8 which is good for a draw or two and then it’s well done.
 

muunch

hotboxing the cockpit
I'm just about to ask this guy if he documented said behavior – owning the TM myself I am very skeptical it is even possible. I might be wrong, of course.

Well, he did say he was using a Mistvape capsule, which does protrude from the stem... seems possible there was a hard short... There seems to be no screen between the heating element and the stem.

vT-WxXP54qNH_dE7xV-6VCVRoo8O7WI4x07KdSD01mi2gZLT5e0X-v3WeOhPe5y8Othk-4fUpubSAWbvp1aQQkSuXt4uGkKngKqV.png


In a quoted email from "the maker" (:rolleyes:) he even says the heating elements do have some variance to them.

" I have seen very hot behavior sometimes, as I said I test them
always with a machine that pulls air trough them and chamomile in the
chamber, and just white ash is left and most disappear completely in a
10 second pull. it was a heater coil that was somehow badly formed and
causing much higher temps to be reached. Only thing I can imagine is
this impact somehow then changed that in your unit. Really special as
we have manufactured about 100, and yeah sometimes such a hot unit
comes out and i need to change the heater and put it back again but
this is the first time such was shipped out, and now already twice.
But some good news - your feedback made me think that maybe there
can be times, that someone would want to have a little bit lower temps
generally, and someone hotter. So I put there now a hidden setting
that makes it possible to adjust the temp selector range -2 or +2
steps from the default, so for example when you would set it to 6, the
temperature would be actually same as now at 4. And yesterday also I
found a way to make the heater more solid in production that makes it
now easier to build them without yet any hot ones appearing. But yes,
thanks for the feedback and maybe your role was now to be an
inspiration for development. I will send you a third one today..sorry
for this again!"

I don't think it's out of the realm of possibility, especially provided the information we have... and I doubt we'll get more info since that guy is banned and "the maker" seems to have an aversion to clearing the air.
 

Siebter

Less soul, more mind
Well, he did say he was using a Mistvape capsule, which does protrude from the stem...

No, it does not. Remember the chamber can be set to any size by moving the cooling unit, so by pushing the capsule in the chamber you would automatically set it to the right size in case it was set to small.

seems possible there was a hard short... There seems to be no screen between the heating element and the stem.

No, there is a screen above the heater too, it has been disassembled for the picture to show the heating element.

That makes it one screen, the herb and a pretty massive cooling unit blocking the way for flames to shoot up the stem – and that's why I am skeptical.

I suggest we stop speculating about that until we have feedback from Cheebachiefer himself – I repeat: I don't know what he's doing there, just saying that I don't see it being possible.
 

AlexT2

Well-Known Member
Hello, this vaporizer is very interesting, it escapes me of price, but an effort could be made.
I have tried to read the whole thread, but I have not been able to find the weight of the unit, it does not appear on its page, can anyone tell me?
 
AlexT2,

RxPlorer

Well-Known Member
I suggest we stop speculating about that until we have feedback from Cheebachiefer himself – I repeat: I don't know what he's doing there, just saying that I don't see it being possible.

if Cheebachiefer is the individual positing about flames shooting up the stem, I stand by my previous statement, full stop. He will continue to post information here and there that appears to be well informed and reasonable, but he is certainly not the latter. He is carefully working the long game to make trouble for the manufacturer in any way possible, which becomes readily apparent as his posts continue. There is zero reason to further speculate or worry about any information that comes through him.

To all y’all that will love to jump on this post; I have no further defense or argument to offer you. This post is for the well intentioned members that are seeking truthful information about a product they’re interested in. To pay any attention to Cheebachiefer is to fall victim to his FUD campaign, just one facet of his long quest to exact vengeance for a perceived slight. Don’t bother with him, life is too short already.
 
Last edited:

dzoinp

Well-Known Member
Accessory Maker
Or are you thinking a way to boost power to finish a bowl without turning the temperature up?
That's what I wanted! boost in on demand mode!
I'm doing 5/6 draws with the dial at 5.155555 and then I go straight to 7.4444 for 2/3 final draws without stirring
If possible I would change the session mode for a boost in on demand mode

maybe people who use rigs prefer session mode, so they don't have to press the button during the draw ... ok I see
I am trying to convince Creator to put the boost option also on demand. I would rather do a boost for the final draws instead of messing with the dial
 
Last edited:

RelaxedNow

Well-Known Member
I’m not a session user, but its handy when sharing with vape novices. No instructions needed, except “Just draw, and be careful, or it’ll surprise you”.

I’m calling bullshit on the missing screen. Anybody following this thread would know it has a screen above the heater. Me thinks @Munch is fucking with our heads. :nod:
 
Last edited:

chunkemup

New Member
Nice try.
if Cheebachiefer is the individual positing about flames shooting up the stem, I stand by my previous statement, full stop. He will continue to post information here and there that appears to be well informed and reasonable, but he is certainly not the latter. He is carefully working the long game to make trouble for the manufacturer in any way possible, which becomes readily apparent as his posts continue. There is zero reason to further speculate or worry about any information that comes through him.

To all y’all that will love to jump on this post; I have no further defense or argument to offer you. This post is for the well intentioned members that are seeking truthful information about a product they’re interested in. To pay any attention to Cheebachiefer is to fall victim to his FUD campaign, just one facet of his long quest to exact vengeance for a perceived slight. Don’t bother with him, life is too short already.

New here glad to join in the fray! Upon review of Vapor Asylumn it would appear to me that Cheebachiefer made a better review than I've seen from most. Devoid of hucksterism and as someone mentioned on VA, it was a very "pragmatic" review. A lot of the "reviews" for the Tinymight look like they were written by a used car salesman on his first day on the lot, lots of hyperbole not so much fact. Seems a few folks have a chubby for this vape, not sure it's warranted. I have used a Tinymight twice now, the sky didn't split open, church bells didn't ring, no widespread panic in the streets. It was an adequate vape, better than a Mighty? Nada.

Also with all due respect, it's kinda creepy to be takin shots @ a person who can't defend themselves, as they were bounced from this site, under dubious circumstances as far as I could research.

Modnote: This is Cheebachiefer in case it's not already painfully obvious.
 
Last edited by a moderator:

Terpenetime

Well-Known Member
New here glad to join in the fray! Upon review of Vapor Asylumn it would appear to me that Cheebachiefer made a better review than I've seen from most. Devoid of hucksterism and as someone mentioned on VA, it was a very "pragmatic" review. A lot of the "reviews" for the Tinymight look like they were written by a used car salesman on his first day on the lot, lots of hyperbole not so much fact. Seems a few folks have a chubby for this vape, not sure it's warranted. I have used a Tinymight twice now, the sky didn't split open, church bells didn't ring, no widespread panic in the streets. It was an adequate vape, better than a Mighty? Nada.

Also with all due respect, it's kinda creepy to be takin shots @ a person who can't defend themselves, as they were bounced from this site, under dubious circumstances as far as I could research.

Hmmm, something fishy going on here :2c:
 

david8613

Well-Known Member
Does someone have a nice video of the tiny might kicking out cool temperature vapor clouds on first draw natively? I have a hard time believing this device can really do it on first draw with out vapor being super hot. All convection devices I have seen and used always give a light first hit and then kick out clouds on the 2nd and third draws like ghost mv1, rbt splinters, grasshopper etc. I can do big clouds on first draw on those devices but only on high setting on temp dial. I have only seen conduction or hybrid devices like mighty, pax, volcano hybrid give big clouds on first draws easily because of all the conduction going on. How does the tinymight do it being 100% convection?
 
david8613,

LabPong

Well-Known Member
Does someone have a nice video of the tiny might kicking out cool temperature vapor clouds on first draw natively? I have a hard time believing this device can really do it on first draw with out vapor being super hot. All convection devices I have seen and used always give a light first hit and then kick out clouds on the 2nd and third draws like ghost mv1, rbt splinters, grasshopper etc. I can do big clouds on first draw on those devices but only on high setting on temp dial. I have only seen conduction or hybrid devices like mighty, pax, volcano hybrid give big clouds on first draws easily because of all the conduction going on. How does the tinymight do it being 100% convection?

It kicks arse on first draws....

You should of ordered this long ago.......don't just sit there and drift on it brah...hurry! ;)
 
Last edited:

Tweakz

Well-Known Member
Does someone have a nice video of the tiny might kicking out cool temperature vapor clouds on first draw natively? I have a hard time believing this device can really do it on first draw with out vapor being super hot. All convection devices I have seen and used always give a light first hit and then kick out clouds on the 2nd and third draws like ghost mv1, rbt splinters, grasshopper etc. I can do big clouds on first draw on those devices but only on high setting on temp dial. I have only seen conduction or hybrid devices like mighty, pax, volcano hybrid give big clouds on first draws easily because of all the conduction going on. How does the tinymight do it being 100% convection?

it’s a beast convection vape



https://www.instagram.com/p/B8RffHtnx2u/?igshid=e6w3dpwnmiys
 

LabPong

Well-Known Member
Yeah man this thing kind of came out no where, and it looks so innocent, it looks nice but it doesn't look like a beast mode vape. I'm hearing it is! Watching this closely, It's on my list.

It gives big powerful vapor at level 6. I use it in a rig and it is by far the closest thing to simulate combusting in a bong that I have vaped so far......it's the fastest vape in the.....(where ever you are). :tup:
 

Siebter

Less soul, more mind
I have a hard time believing this device can really do it on first draw with out vapor being super hot.

I honestly give you my word for it. I'm not trying to push or hype the TM at all, I don't give a fuck what anyones vaping on – I'm actually hoping that the demand for TMs these days won't crush this company in one way or another. But the demand and praise is justified, esp. when it comes to performance vs. ease of use vs. coolness – *anyone* can have huge, yet cool clouds with this thing, right away, at first draw. You won't have to fear wispy first draws, but rather going too far with your first hit.

True story.
 

dzoinp

Well-Known Member
Accessory Maker
Does someone have a nice video of the tiny might kicking out cool temperature vapor clouds on first draw natively? I have a hard time believing this device can really do it on first draw with out vapor being super hot. All convection devices I have seen and used always give a light first hit and then kick out clouds on the 2nd and third draws like ghost mv1, rbt splinters, grasshopper etc. I can do big clouds on first draw on those devices but only on high setting on temp dial. I have only seen conduction or hybrid devices like mighty, pax, volcano hybrid give big clouds on first draws easily because of all the conduction going on. How does the tinymight do it being 100% convection?

don't want a big clould on first draw? ok put the dial at 4... light and tasty vapor:brow:

If you set it above 6, be careful with the steam power, never with its temperature. (with the CU)

If you ever try the TM ask someone to pinch you so you can see that you are not dreaming:lmao:
 

YaMon

Vaping since 2010
There's been some posts here about the Grav stems, so I purchased three different Grav stems with a 20% coupon I had. The GRAV® Glass Blunt w/ Silicone Grommet, the GRAV® Upline® Taster and the 16mm GRAV® Octotaster. The Upline Taster and 16mm Octotaster are both just slightly to big to fit, perhaps if I removed the red o-ring, but for me it's not worth mucking with. The Glass Blunt definitely has a much smaller OD and is just not a fit. This was my attempt however feeble to replace the stock stem and cooling unit. The only issue this 'fan boy' has with the TM is the delicate o-rings around the cooling unit (CU) and not having a spare screen for the CU. I do have spare o-rings and have used two as I stretched the original two out of shape siding the CU out of the stem without using my breath to first fog the inside of the stem.

 
YaMon,
  • Like
Reactions: BigJr48

Tweakz

Well-Known Member
don't want a big clould on first draw? ok put the dial at 4... light and tasty vapor:brow:

If you set it above 6, be careful with the steam power, never with its temperature. (with the CU)

If you ever try the TM ask someone to pinch you so you can see that you are not dreaming:lmao:

for almost 4 weeks now I just want to pay for my order ... but they don’t give me .. there is still no credit card payment on the site .. can someone help.
 
Tweakz,

fogbank

Well-Known Member
Would anyone know how the TM stacks up against FireFly 2, please? :)

You are comparing fairly different vapes. The biggest diff is the power of the vapor. Tinymight will be much much more powerful with its heating design. The FF2 will give you better taste maybe....that would be personal though. So I would personally sum it up by saying the FF2 is more like a sipper box and the Tinymight is more like the heavy medicator if you need.

Before I got my Grasshoppers the FF2 was my daily driver (and the FF1 was my DD before that). I can just add that the TM is easier to use than the FF2. The FF2 had a learning curve for me that the TM never has. I’ve gotten good vapor from my first draw on the TM. A few months ago I broke out my FF2, after many months of non-use. I couldn’t even get the right technique to get decent vapor.

The TM can also produce vapor more quickly than the FF2. The TM has a less restricted draw.
 

Stu

Maconheiro
Staff member
New here glad to join in the fray! Upon review of Vapor Asylumn it would appear to me that Cheebachiefer made a better review than I've seen from most. Devoid of hucksterism and as someone mentioned on VA, it was a very "pragmatic" review. A lot of the "reviews" for the Tinymight look like they were written by a used car salesman on his first day on the lot, lots of hyperbole not so much fact. Seems a few folks have a chubby for this vape, not sure it's warranted. I have used a Tinymight twice now, the sky didn't split open, church bells didn't ring, no widespread panic in the streets. It was an adequate vape, better than a Mighty? Nada.

Also with all due respect, it's kinda creepy to be takin shots @ a person who can't defend themselves, as they were bounced from this site, under dubious circumstances as far as I could research.
Nice try, Cheebachiefer. :goon:

This is your third account that you've tried to make since getting banned here, and I'll just keep banning your new ones so you might as well stop wasting both of our time.

:peace:
 
Top Bottom