TinyMight / TM 2

[Vaporific]

There are the European and the American site...

If you’re referring to https://www.kgwoodcrafts.com/product-page/tinymight-vaporizers as the American site, it’s been out of stock for a while. I believe she’s waiting on more production inventory from the Tinymight maker (THE source).

Tales from the Tinymight honeymoon: I’m still using a simple dome screen below the CU herb chamber and I’ve moved it back further up the (short) stem just a tad, a millimeter or two, to solve the ring-y AVB I’ve been noticing. So far so good. Still a bit ring-y but a bit more consistent. Regardless, the TM vapor is so cool and a pleasure to use. Effect is unreal and unmatched compared to the various vapes I own and have tried. It’s a fantastic vape, plain and simple.

 

[YaMon]

If you’re referring to https://www.kgwoodcrafts.com/product-page/tinymight-vaporizers as the American site, it’s been out of stock for a while. I believe she’s waiting on more production inventory from the Tinymight maker (THE source).

I have yet to hear of any USA based supplier ever having a TM for sale, only EMEA based vendors have been able to supply this vape in limited quantities. I suspect we will hear from USA based suppliers should they ever obtain stock.

 

[chicago_animal]

I have yet to hear of any USA based supplier ever having a TM for sale, only EMEA based vendors have been able to supply this vape in limited quantities. I suspect we will hear from USA based suppliers should they ever obtain stock.

Which ones are EMEA based?

 

[murf2010]

I used PayPal and it just says pending for the last few days. Does it not actually charge you till the product ships?

 

[LabPong]

I used PayPal and it just says pending for the last few days. Does it not actually charge you till the product ships?

Yes....the payment is in hold for 30 days....if the vape is not ready to ship...the order will be dropped from PP and the pending status...but he still has your order...you just need to watch and reorder every 30 days.

That is pretty much how he did it from the start.....seems like it is the same now.

 

[murf2010]

Yes....the payment is in hold for 30 days....if the vape is not ready to ship...the order will be dropped from PP and the pending status...but he still has your order...you just need to watch and reorder every 30 days.

That is pretty much how he did it from the start.....seems like it is the same now.

Ok that’s what I figured.

 

[YaMon]

Which ones are EMEA based?

I know VapeFiend had them, but sold out quickly. Another member mentioned a vendor in France had them, but no name given.

 

[Momor]

Which ones are EMEA based?

I know VapeFiend had them, but sold out quickly. Another member mentioned a vendor in France had them, but no name given.

Here they are (at least the one i know for now) :

https://www.docteur-vaporisateur.co...les/1146-tinymight-vaporisateur-portable.html

https://www.vaporisateur.net/tinymi...ur-a-chauffe-par-convection-a-la-demande.html

https://lacentralevapeur.com/vaporisateurs-portables/23192661-pre-commande-tinymight-vaporizer.html

https://jahvaporizer.com/portable-vaporizer/23192661-tinymight-vaporizer.html (same shop as La Centrale Vapeur but with another website, i don't know why)

 

[dzoinp]

If you’re referring to

no... i'm referring to this:

https://tinymightvape.com/tinymightvape.eu/index.php?route=account/login

https://tinymightvape.com/index.php?route=account/login

 

[Vaporific]

no... i'm referring to this:

https://tinymightvape.com/tinymightvape.eu/index.php?route=account/login

https://tinymightvape.com/index.php?route=account/login

The first link opens in Finnish (I think) however isn’t the main URL supported by the Tinymight maker himself? The second link, same domain really, is in English (good for me). That’s the site mine was ordered from (a friend’s accidental second order which I paid him for - hey I took one for the team ). I don’t want to quibble. All I know is this vape works well and is now my number one, daily vape. And I’d recommend this vape to anyone, it’s that great. Life is good even for a Tuesday. Cheers!

 

[dimmusp]

Effect is unreal and unmatched compared to the various vapes I own and have tried. It’s a fantastic vape, plain and simple.

Wow! What other vapes have you owned/tried?

 

[Catnipmint]

Sorry for multiple post, dont know why working. Pictures are about a Splinter translucent stem with EVO ELB cutted back and used Saionaras and EVO stems cap as caps. Dismantling an EVO ELB is not easy, the bigger cup can be cutted with scissors, but the cap... try to loosen the rim and pull out the mesh. Splinter for rig use, and long stem with moded CU for on the go. Modded CU: removed all of the spacers and added one more nut for more airflow.

Modnote: Edited to display image

 

[Shit Snacks]

https://ibb.co/P6VRJy1

Paste the bb code, not the link or url brackets

 

[Vaporific]

Wow! What other vapes have you owned/tried?

Pax, Firefly, Fury 2, Grasshopper, Miqro, Dynavap, and a few other portables; Aeromed(!) and HerbalAire in the desktop category. I don’t own desktops but Aeromed is pretty phenomenal, but I love the Tinymight. Perfect for me!

 

[lauantaimakkara]

How do you stir your material? I find it quite difficult and usually some of the material drips onto the floor. or do you pack your material loosely to make it easier to stir?

sorry my English is not very good I hope you understand what I meant

 

[YaMon]

How do you stir your material? I find it quite difficult and usually some of the material drips onto the floor. or do you pack your material loosely to make it easier to stir?

sorry my English is not very good I hope you understand what I meant

While the need to stir with the TM is negligible, if required you remove the stem and insert a pick in the stem and stir. Once stirred I usually use the back end of a Bic Ball Point pen as it is just the right size to tap what is in the stem. Then place the stem back in the TM and have a rip. TM is a great extractor and there is seldom enough left to warrant stirring if you are temp stepping. I usually begin and spend most of my session on a heat setting around 6 and then when the vapor is light I go to 8. When at 8 and no vapor I may stir, but there will only be 1 good draw left at that point.

 

[Vaporific]

While the need to stir with the TM is negligible, if required you remove the stem and insert a pick in the stem and stir. Once stirred I usually use the back end of a Bic Ball Point pen as it is just the right size to tap what is in the stem. Then place the stem back in the TM and have a rip. TM is a great extractor and there is seldom enough left to warrant stirring if you are temp stepping. I usually begin and spend most of my session on a heat setting around 6 and then when the vapor is light I go to 8. When at 8 and no vapor I may stir, but there will only be 1 good draw left at that point.

It should go without saying - and hey, I’m Captain Obvious - when you remove the stem hold it so the material is facing up before you stir. I know, I know it’s obvious but just for the record. Indeed once you do stir you’ll likely need to tamp the material down again to prevent any into falling into the bottom of the heating chamber. I’m avoiding stirring when I can though and concur with the last draw to finish/kill the load - bump up the temp and take one last draw. I usually can get something, if not vapor, then effect from finishing a load. It’s one of the cool things about the Tinymight...

 

[Shit Snacks]

How do you stir your material? I find it quite difficult and usually some of the material drips onto the floor. or do you pack your material loosely to make it easier to stir?

sorry my English is not very good I hope you understand what I meant

I find no reason to stir really, I even tried it yesterday and it really didn't make a difference for me... if you want though just try dumping out the entire stem on a surface and then just sucking it back up like a straw in reverse order

 

[SquirrelMaster]

I had a small package show up today (ordered March 10) that I had completely forgot about. Thank you @Abysmal Vapor for the tip on the Airistech Bubbler http://fuckcombustion.com/threads/tinymight-vaporizer.44563/page-87#post-1453913
I bought mine through Aliexpress for $5.02 USD (shipped) and from an initial inspection and function test I'm really impressed. It fits perfectly in my unit and has a nice deep 25mm bowl. I can't wait to test this little guy out.



Function Video
https://i.imgur.com/1uZte0x.mp4

 

[murf2010]

I had a small package show up today (ordered March 10) that I had completely forgot about. Thank you @Abysmal Vapor for the tip on the Airistech Bubbler http://fuckcombustion.com/threads/tinymight-vaporizer.44563/page-87#post-1453913
I bought mine through Aliexpress for $5.02 USD (shipped) and from an initial inspection and function test I'm really impressed. It fits perfectly in my unit and has a nice deep 25mm bowl. I can't wait to test this little guy out.



Function Video
https://i.imgur.com/1uZte0x.mp4

Looks amazing.

 

[bornfree13]

I just found Tinymights in stock over here in Europe for a killer price, the shop is legit!
No idea if this is a mistake but its 230 Euros with free 24h express shipping
Their partner shop in France says they will be available April 10th, but here it says in stock so be ready for mistakes, but you might end up getting one for a very good price anyway!

https://jahvaporizer.com/portable-vaporizer/23192661-tinymight-vaporizer.html

High

Has anyone else got the tinyMight from this site? How long did it take?

 

[Brewervapesalot]

I had a small package show up today (ordered March 10) that I had completely forgot about. Thank you @Abysmal Vapor for the tip on the Airistech Bubbler http://fuckcombustion.com/threads/tinymight-vaporizer.44563/page-87#post-1453913
I bought mine through Aliexpress for $5.02 USD (shipped) and from an initial inspection and function test I'm really impressed. It fits perfectly in my unit and has a nice deep 25mm bowl. I can't wait to test this little guy out.



Function Video
https://i.imgur.com/1uZte0x.mp4

I like this bubbler too. But the water needs refilling pretty often. Not practical on the go. So I've just been using an Evo hydro tube mostly for water filtration at home.. .. that's fantastic

 

[SquirrelMaster]

I like this bubbler too. But the water needs refilling pretty often. Not practical on the go. So I've just been using an Evo hydro tube mostly for water filtration at home.. .. that's fantastic

I would be afraid to take it on the go, it would definitely have to be separate from the Tinymight but I can see what you mean about refilling. Have you tried it dry, I wonder how it compares to the CU? If my chest was feeling better I would have ripped a few by now. I love my hydratubes but they can be unwieldy for such a little vape. Excellent filtration though and much better for the internals not having to invert the unit.

 

[Brewervapesalot]

I would be afraid to take it on the go, it would definitely have to be separate from the Tinymight but I can see what you mean about refilling. Have you tried it dry, I wonder how it compares to the CU? If my chest was feeling better I would have ripped a few by now. I love my hydratubes but they can be unwieldy for such a little vape. Excellent filtration though and much better for the internals not having to invert the unit.

It's okay dry. Nothing is bad with tiny might.

My go to stems are are 18 mil joint for the hydratube if I want water, and if I don't, then stock with cooling unit or grav stem with tapered tip and cooling rings and just 1/2 standard screen for best flavor.

The hydratube is not unwieldy if you hold it and just bring the tiny might to it.... easier than a plugged in Evo for sure...

 

[Ipe17]

High

Has anyone else got the tinyMight from this site? How long did it take?

Hi,
I did a couple of weeks ago since it looked like they had it in stock. I placed the order and they never charged my credit card. Sent an email and they said they are out of scope and not knowing when they will have stock again (due to covid19).

I may end up cancelling the order.... and waiting foe shops to have enough stock. I dont fancy having to wait and having something pending on my credit card.

cheers