• Do NOT click on any vaporpedia.com links. The domain has been compromised and will attempt to infect your system. See https://fuckcombustion.com/threads/warning-vaporpedia-com-has-been-compromised.54960/.

Life Saber (LSV) by Elev8 Vehicles

AJS

Calm Consistency
Mine is currently In Transit from Missouri. I'm keeping my hopes up for Friday...seems promising enough. (I even looked up driving distance from Missouri to Florida...It's possible!)
I hope this thread is prepared for dozens of videos flooding in of milky white-walled rips.
 

AJS

Calm Consistency
M2_M.jpg

you can install a screen like so, fitting screens are provided, the transfer wand has a screen installed in the same way.
Soo.basically, I take the screens I ordered, put them dome side up, slide it through the top until it hits the bottom of the first male end?
 
AJS,
  • Like
Reactions: grokit

srama21

Monotonous Botanist
My delivery is delayed. I think monday is my best case scenario. Looking forward to seeing your milk shots as a pregame @AJS
 
srama21,

AJS

Calm Consistency
My delivery is delayed. I think monday is my best case scenario. Looking forward to seeing your milk shots as a pregame @AJS
AW MAN! sorry to hear that brother. Mine was delivered at noon, just praying my school organizes it and sends it out to me before they close!

'zacly

m2ms from dhgate bubblers usually have a small ring at the bottom of the joints where the screen can sit.
Thank you man. Hope I can manage, haha.
 

Justpassedu

Well-Known Member
So this is what i am noticing with my lsv so far , i am not 100% sure at what exact point to attach my temp knob. I switched from the glass knob i have back to stock and just stuck it on there a little before 0. The short wpa is awesome with glass rips , i take the top cover off ( Unscrew) and just invert the lsv into the wpa at around 11:30 to 12:30 and get huge lung busting rips , stir after every two hits and it seems i get allot out of a little of material which is great. Now with the wand i notice if using that same temp i will combust sometimes , seems i have to turn the temp to almost 10 to not combust as i feel the material falls down a bit to the heater. Same results with basket screens , they bring the material very close to the heater and unless i am at a super low temp i will combust. Now i have to clean my wands bc they taste nasty. Wpa is a game changer though , milks every piece i have and is just what i been looking for. It is making want to buy more glass.
 

Justpassedu

Well-Known Member
Just got my LSV guys...what exactly do I do with the heater/cover? What get's moved, the glass or the heater. thanks
Just go use it man , get ripped . I am not even sure what gets removed or not but i'd like to know also. I can tell you this though , if using the wpa remove the top part above the heater , it unscrews by hand , pack the wpa , insert into one of your 18mm water pipes , turn dial on lsv to 12 , let it warm up for 5minutes and prepare to get amazed.
 
Justpassedu,

AJS

Calm Consistency
I've been rippin it, can't get as thick of hit as I want so I think the glass might be too far up.
It's really difficult to slide down tho so I'm refusing to go lower til I hear feedback.

Also...I don't have any domed screens, I just have regular 14.8mm screens and 20mm that they gave me and I can't get them to stay in my m2m very well. Any suggestions?
 

Justpassedu

Well-Known Member
oh i got you , here this may help , found it on you tube :

Did you get the wpa from 7th floor bc it works awesome for me so far ? I'd say try cutting the screens a bit and playing with them , i only tried my m2m with a elbow screen so far from my Eq vape.
 
Justpassedu,

VAPORIZER22

Well-Known Member
I've been rippin it, can't get as thick of hit as I want so I think the glass might be too far up.
It's really difficult to slide down tho so I'm refusing to go lower til I hear feedback.

Also...I don't have any domed screens, I just have regular 14.8mm screens and 20mm that they gave me and I can't get them to stay in my m2m very well. Any suggestions?

The heating element may need to be pulled out. Towards the bottom of the heating element it will say STD-1, it has been suggested that the element should be pulled out gently so you can at least see the dash, of course wait it has cooled down.
 
Last edited:

AJS

Calm Consistency
I'm pulling on the ceramic with my fingers, and it tugs a bit, and if I let go it just settles back where it started. I feel like I'm fighting something, I'm scared to do anything, haha.

Edit: And I most certainly don't see any STD's flyin around these parts...I see ink smudges it seems but no STD. Maybe my heater is just that low? My 3:00 yellows my herb. Faaaat hits, but could only yellow it.
 
AJS,

KidFated.

Unknown Member
I'm pulling on the ceramic with my fingers, and it tugs a bit, and if I let go it just settles back where it started. I feel like I'm fighting something, I'm scared to do anything, haha.

Edit: And I most certainly don't see any STD's flyin around these parts...I see ink smudges it seems but no STD. Maybe my heater is just that low? My 3:00 yellows my herb. Faaaat hits, but could only yellow it.
Try twisting slightly as you pull up
 

VAPORIZER22

Well-Known Member
Try twisting slightly as you pull up

Yup, forgot to include to twist and pull gently. AJS, if your at 3 on the dial and only get yellow herb your heating element does need to be pulled out a bit. I can see about half the dash on my LSV and I start at 12 and get tasty good vapor and take my last hit at around 2:30 and I get dark brown herb at the end of my session.
 
VAPORIZER22,

AJS

Calm Consistency
alright wonderful, I managed to get the heater pulled out to a perfect distance...buuut, now the glass isn't aligned..to the point of not being able to screw the lid on. am I allowed to just pull on it sideways? what's the best method to get the glass aligned....and also the heater, the heater is a bit slanted.
 
AJS,

KidFated.

Unknown Member
alright wonderful, I managed to get the heater pulled out to a perfect distance...buuut, now the glass isn't aligned..to the point of not being able to screw the lid on. am I allowed to just pull on it sideways? what's the best method to get the glass aligned....and also the heater, the heater is a bit slanted.
The heater doesn't need to be straight, but push the heater cover all the way in and it should fit enough to get the lid on
 
KidFated.,

AJS

Calm Consistency
Disregard everything, just turned on the LSV and the light flickered and turned off. Won't turn back on. Tried diff outlets.
Anything...?
Disappointing
 
AJS,

KidFated.

Unknown Member
Disregard everything, just turned on the LSV and the light flickered and turned off. Won't turn back on. Tried diff outlets.
Anything...?
Disappointing
Loose connection somewhere, I'd get a warranty started. Sucks.. Truly is a beast.. 7th floor will take care of you
 

AJS

Calm Consistency
Dimmer blew a fuse. Hopefully I get tons of free shit for this. At least I got to experience it for a little bit.
 
AJS,
Top Bottom