JoDa Glassworks

flotntoke

flotntoke

thoroughly vaped
Oh man!! Another gorgeous piece!!!!!!:tup:

Really love the swirls (twists?) and the swiss percs to keep water in control in both of these. Have a similar inline with triple donut that I love to use for vaping. Nowhere near as nice as either of these lovelies, though. Very easy to maintain flavor while vaping with one of these by keeping the draw slow until you clear, and love doing dabs from mine.

That swiss perced mouthpiece is truly a thing of beauty, too! Great work!! :wave:
 
Bravesst

Bravesst

Full Steam Ahead
Manufacturer
Is there any truth to the reduction of OD for AA and Solo stems in the future? My current Joda short stem (picked it up on Puffitup) is unable to fit into either my two Airs or Solo. It's a great look, fine piece of art, love to get to use it soon.
 
Bravesst

Bravesst

Full Steam Ahead
Manufacturer
VaPeD&CoNfUsEd said:
It should fit great as each one is fit by hand before they go out. They are a tight fit at first until the Orings get a little stretched to them. Have you tried fitting it while the unit is hot?
Click to expand...
Great Piece!
I'm not using O-rings in the Solo, and none obviously in the Air. Just real tight even red hot. I'll give it another go tomorrow. I'm sure it's just me. Awesome product!!!
 
Trogdor

Trogdor

Vapinating the peasants
VaPeD&CoNfUsEd said:
I mean the factory Orings. The ones that are built into it. I can't believe it doesn't fit in any of them. Even if they are super tight for the air it should be nice and smooth in the solo. As there is a bit of a difference in the diameter of the 2.
Click to expand...

How old was the test fit solo? perhaps different models have differences in oven diameter. On my solo I couldn't even get it past the metal cap, had to sand it out a bit. I also replaced the little plastic ring with 3 PIU silicone o-rings since it was quite tight, now the stem works like a charm.
 
Nugg

Nugg

Well-Known Member
@VaPeD&CoNfUsEd have you got a factory solo stem? If so how tight/loose is it in the solo?

If you take the top off the solo so you can see the standard o ring thing. If you push down on that with the back of a spoon it tightens up the oven a bit and makes it hold on to normal stems really well.


I think your test fit solo might need a little tighten up?
 
VaPeD&CoNfUsEd

VaPeD&CoNfUsEd

JoDa Glassworks
Glass Blower
These are pieces you guys have seen but they are some real pro looking pics of them. My shopmate/apprentice 's wife is an aspiring photographer and has a real eye for photographing glass to show you a close representation of what we see in person. Please, if your on IG check out @ASHBASHFORCASH and my shopmate @DONDOOBIOUS to see her work and to see just how far he's come in just 4 months.

CiNrXtf.jpg

Available^^^
J2Xr4MR.jpg

Sold^^^
9Bqau2q.jpg

Available^^^ and would do a matching drop down like the blue one.
 
Bravesst

Bravesst

Full Steam Ahead
Manufacturer
VaPeD&CoNfUsEd said:
I mean the factory Orings. The ones that are built into it. I can't believe it doesn't fit in any of them. Even if they are super tight for the air it should be nice and smooth in the solo. As there is a bit of a difference in the diameter of the 2.
Click to expand...
There is an obvious ID diff with AA and Solo. Most of my Solo stems are quite loose (except one bent stem). My Solo is about a month old from Puffitup. I'm gonna warm the oven nice and hot (use another stem) and retry... no worries,

@VaPeD&CoNfUsEd
Somehow got it into my AA , best performance ever --- smooth as silk!!! Just real tight - hard time rotating to remove, just a bit of a concern on stretching seal. SO MUCH AIR, very nice!!!
 
Last edited by a moderator:
jojo0420

jojo0420

Cloud Chaser
Bravesst said:
@VaPeD&CoNfUsEd
Somehow got it into my AA , best performance ever --- smooth as silk!!! Just real tight - hard time rotating to remove, just a bit of a concern on stretching seal. SO MUCH AIR!!!
Click to expand...

I've been using several of JoDa's stems in my air now, and they were pretty snug at first but now they fit a lot better and my stock stems still fits plenty tight. They won't fall out if I turn it upside down.
 
Last edited:
Frederick McGuire

Frederick McGuire

Aggressively Loungey
VaPeD&CoNfUsEd said:
Sorry for the absence as of late guys. I've had some incredibly trying times in my personal life. I'm getting back into full swing now though.

On a side note:
9pUkXlj.jpg

Watch for some accessories for this lil guy very soon.
Click to expand...
Aww shit :D
Whatever you come up with for the GH, I think I wanna be in on that :D

I should probably wait until I actually get my GH (:lol:), but I wanted to officially declare my interest :)
 
flotntoke

flotntoke

thoroughly vaped
Hope all is going OK @VaPeD&CoNfUsEd - or at least better than it has been.

Screw the GH and the years of associated nonsense!!! Let's get ready to start talking custom glass for this puppy. Am guessing there will probably be more in new owners hands sooner anyway. If you don't recognize it, you should check the thread. Zion!

TcdALH1.jpg


Thanks in advance to @Shit Snacks for providing the nice pic!
 
Mulehead

Mulehead

Well-Known Member
flotntoke said:
Hope all is going OK @VaPeD&CoNfUsEd - or at least better than it has been.

Screw the GH and the years of associated nonsense!!! Let's get ready to start talking custom glass for this puppy. Am guessing there will probably be more in new owners hands sooner anyway. If you don't recognize it, you should check the thread. Zion!

TcdALH1.jpg


Thanks in advance to @Shit Snacks for providing the nice pic!
Click to expand...
You beat me to it @flotntoke! Was fixing to send Josh a PM, to start the design process. The Zion stems need to be US 18mm male, and not ISO. I believe all my other JoDa pieces are the US? Is that correct, is that your standard 18mm male @VaPeD&CoNfUsEd ?
 
NickDlow

NickDlow

Log Hog
Mulehead said:
You beat me to it @flotntoke! Was fixing to send Josh a PM, to start the design process. The Zion stems need to be US 18mm male, and not ISO. I believe all my other JoDa pieces are the US? Is that correct, is that your standard 18mm male @VaPeD&CoNfUsEd ?
Click to expand...

Anyway u look at it millimeters are metric. 18mm in the U.S. is the same as 18mm anywhere else. Just sayin.
 
You must log in or register to reply here.
Top Bottom