QWISO for electronic cigarette juice

Striker Titan

New Member
Fist post so any suggestions welcome.
I have been working on a tech for producing a good ecig juice. I wold really just like suggestions or guidance on the method being used. I will try to update this with photos soon.

AMT UNIT INGREDIENTS
5 gm. Plant material (flowers) - Ground
10 ml Propylene Glycol
1 ml Vegetable Glycerin
1 N/A 99% Isopropyl Alcohol

QTY KIT Comments
3 Mason jar with canning lid Ball mason jars
1 Strainer I use a nut milk bag
1 10 micron screen
1 Double boiler I use a 4 cup Pyrex and a 2 qt boiling pot
1 10 ml syringe with tip Medical grade.
1 Laser thermometer
1 1oz glass bottle with eye dropper.
1 Suspension system for the 1oz glass bottle. I use floss to hang the bottle. Go McGyver on it.


For clarification of the below ( 3 jars are used in total)

1st jar Extraction - Plant material goes in with iso
2nd jar Strain - Used with nut milk bag to remove most plant material. The 10 micron will be place on this prior to the product being transferred to the collection jar.
3rd jar Collection - Used to collect final pre purge solution.


PROCEDURES
1. In a 1 stage grinder. Coarse grind the plant material
2. Seal the plant material in a mason jar (extraction jar). Place the sealed extraction jar and the bottle of Isopropyl Alcohol in to the freezer for 24 hours.
2a. Prepare the (strainer jar) and the 10 micron screen for extraction.
3. Add Isopropyl Alcohol to the extraction jar until the plant material is fully submerged. Agitate the solution lightly for 10 seconds to ensure that all the plant material is saturated. Immediately return to the freezer for 5 minuets.
4. Dump the ISO/Plant material solution in to the strainer jar fitted with the nut milk bag.
5. Use a small amount of ISO to clean the extraction jar and dump this through the nut milk bag containing the plant material.
6. Do not squeeze the material in the strainer. Allow it to drip out until the liquid stops or the drips begin to take on a dark color.
7. Place the prepared 10 micron filter on the strainer jar. Place the jar upside down on to the collection jar and return to the freezer. Allow the solution to drip through.


8. Prepare double boiler. Water temperature to be at 150° - 185°. 150° is best for the initial phases
9. Remove the collection jar and place contents into the top of the double boiler
10. The ISO will slowly evaporate off time will depend on temperature/atmospheric pressure/quantity of solution.
11. As the solution boils down you will begin to notice micro bubbles in the oil. These are small amounts of ISO that need to be purged. The boiling point of ISO is 180° You will need to agitate the oil to release all of the bubbles. (This is time consuming but necessary). Once the oil is maintaining 180° and not producing micro bubbles the process is complete.
12. Remove the top of the double boiler.
13. Reduce water heat to its lowest setting.
13. Add 10 ml of Propylene Glycol to the extract .
14. Add 1 ml of Vegetable Glycerin to the extract.
15. Mix the PG/VG/Oil solution until the water has stabilized at its lowest setting. This may require scraping the dry/hard oil off of the bottom of the container.
NOTE: The end result may have a chunk of oil that does not seem to dissolve. This is ok it will break down during suspended decarb.
16. Return the purge container to the double boiler. Set it on an edge so you can collect any remaining solution.
17. Transfer the solution and any remaining oil collections to the 30 ml apothecary bottle
NOTE: The following step is the decarboxylation process. Some decarb has already take place during the purge. However exact ratios are impossible to determine at the moment. By preforming a post production decarb the product ends with a golden color instead of the traditional green brown.
18. Suspend the apothecary bottle in the water (220°) for up to 45 minuets agitating every 15.
Optional Ultra sonic bath
19. Remove the bottle from the suspension and submerse in an hot water Ultra sonic bath for up to 15 min.

This is the result of several variations on my method. I would truly appreciate any tips/ tricks/ education on better practices.
 
Last edited:

Hashtag46&2

Trichome Technician
Thanks for sharing this...

I've been looking for different recipes to accomplish this, I think my issues are I'm trying to add wayy too much Solid Hash-Oil.

I have several slabs chilling in the Freezer (no pun intended)

So, about how many grams of hash-oil to the ratio of 10ml PG 1ml VG?

I also prefer the PG over the VG, so your recipe has me intrigued for sure.

I would love to blow thick huge "white-out" clouds that come from my E-cig, but with Canna-juice.

Oh. .And OT a bit...

But, thanks to FC..
After 23 years of combustion both Cannabis & Tobacco....

I've been combustion free from cannabis for 7 weeks, cigarettes... 4 days!

Can already feel the difference.

I love this site!!!
 
Hashtag46&2,
Top Bottom