E-Nano from Epickai
I bought my exotic Afzelia burl nano back in July 2014. I haven't purchased a new vaporizer since then. I'd say it's a pretty good VAS cure.
p1ssbucket
Well-Known Member
Same here. I only bought a mighty because I needed something portable that could hit nearly as hard as my nano. I love my nano. Hopefully the mighty holds up to my standards the nano has set?
Well I don't really count the cloud I picked up recently because it was so cheap and a rare find.
Well I don't really count the cloud I picked up recently because it was so cheap and a rare find.
True, I'm still hunting for a good portable to pair with my Nano. I like my Lotus, but it's not stealth enough for my portable needs.
p1ssbucket
Well-Known Member
Stealth isn't much of a factor for me, my criteria was just battery power and heavy hitting. Have you looked at the air? It hits pretty good for a stealthy portable IMO and is really incredible at low temps.
brandonflav
mastermind behind the great Vapor Caper
Congrats on the purchase! Can't wait to get a little more $ put to the side so I can finally pull the trigger myself on one of these beauties.
When that day comes, I'll be shooting a PM @Ratchett for some adapters.
ataxian
PALE BLUE DOT
I have used a NANO and a VAP2 as desktops!
Portable the SOLO has been my portable.
The LOTUS is a powerful little guy however not stealth at all!
The Firefly is sweet and stealthy. Just make sure the battery is a 570 and not a 550.
This is my stealth machine.
The LSV was good however the NANO was easier for me to use.
ÀIR IS NEXT.
Last edited:
flotntoke
thoroughly vaped
Once it's up to temp it should hang pretty close to the same. But, little things can make a difference. All the stuff @Ratchett mentioned, even little things like power change from an extension cord or surge suppressor can have a small effect. Don't forget your draw speed will change heat a little, too.
Check out the Cheap High Quality Bubbler thread if you haven't, yet. Plenty of cheap rigs that pair well with the nano. And as it sounds like you're finding, less is more when it comes to diffusion. This especially true with the nano's great flavor on most strains. Definitely don't want to knock that back.
Probably longer - at least for home use. I quit looking at most stuff after I got the nano. Portables? That's a different story.
Reflections
Well-Known Member
Lou Taylor
Well-Known Member
NickDlow
Log Hog
Read the last two pages and you will see why it's not...
sounds like your heat core might be making contact with the load. Either use a smaller size load, or push the screen further away from the heat.
I typically install my basket screens 15mm deep, and load approximately 0.1g (or less) per load.
mixchu69
Well-Known Member
Thanks Ratchett. I think I am going to try holding onto the nano and move it around while I take a draw or lessen the heat.
I do that sometimes when I wanna pack a huge load. Just leave enough space to fit the core 2mm into the stem and hold it there. Beautiful flavorful hits.
flotntoke
thoroughly vaped
Depends on your heat setting and your GonG. Does the nano sit perfectly perpendicular on it? If not, this is why one side is darker. Whatever is darker is because of heat, distance and time on there. I usually don't leave mine perched on top for more than a few minutes.
mixchu69
Well-Known Member
I don't think it sits perfectly flush. I was having fantastic results when I first started. Maybe it's the new surge protector I bought.
Diehard, I did the same.
Edit: what is your favorite way to use the enano? I know this beautiful wood heater has all the goods but I am just using it wrong. All my problems from user error most of the time 90%. And I am going to buy better surge protector. I want to love it because of its artistic look and reliable heater design. I am trying to get the right setup. Bought the d020 d, fc187 and some other China pieces.
Last edited:
BoogerMan
Well-Known Member
Can you post a pic or link of your Ramon Burl Nano?
That was one type of wood I was interested in from Snappo! Thanks!
EverythingsHazy
Well-Known Member
Just under 7 on the dial (this varies a bit between each nano, and based on the ambient room temp), and 0.03-0.05g in the gong. First hit, the nano is held (by hand) higher than where it would rest if let to sit on the gong by itself. The gong is also spun around a bit, and the nano moved around to hit the entire top of the load. Then the stuff is stirred, and usually the load shrinks due to moisture loss, and then the nano can sit on the gong for hits 2-3. You want to avoid having the heater screen touch the herb to prevent hot spots, blackening, and possible combustion.
You can re-fill the gong as many times as you want, but using small amounts multiple times tastes better than using one big load and taking more hits off of it. More fresh green hits with multiple smaller loads.
mixchu69
Well-Known Member
That is awesome advice. Thanks EverythingsHazy, I knew it was user error.
p1ssbucket
Well-Known Member
Yeah if my experience with the all glass gong has taught me anything the less you put in the nano the better it seems to hit