• Do NOT click on any vaporpedia.com links. The domain has been compromised and will attempt to infect your system. See https://fuckcombustion.com/threads/warning-vaporpedia-com-has-been-compromised.54960/.

Nok21

Well-Known Member
Go for the nano blindly!!!!
-with a stem and the basket screen really low you can shove 0.3+g easily
-yes, yes
-yes
-?
-Yes -10% and life warranty with FCLOVE
-no , any gunk is brunt pretty fast and remains few white powder ash you brush or blow.


-Typo edited and replaced with question.

Life warranty to people on FC you say? Works with oils and hard concentrates? Damn im about sold!

Only question i have left: What kind of maintenance is needed to keep the E-Nano functioning properly? Other than cleaning your glass stem of course. Oh, and do i need to create an account on their website to verify that i am a FC member?
 

Kief

Medicated
Life warranty to people on FC you say?... Oh, and do i need to create an account on their website to verify that i am a FC member?
Just use that coupon code.
Damn im about sold!
You can't go wrong... even if you don't like it, these things hold their value and sell easy.
What kind of maintenance is needed to keep the E-Nano functioning properly?
I haven't done anything but brush out a little dust a few times in the last 2 years.
 

Enchantre

Oil Painter
Im heavily considering picking up an E-Nano after my thread in ask FC, so i figure for more specific info i'd come here. Currently torn between the E-Nano and Arizer extreme Q.

Just a few questions to E-Nano owners (Or the manufacturer).
-How much can be loaded into the E-Nano?
-Can it be used with concentrates, both hard and oils?
-Does the VVPS show you what temperature/ have temp markers on it?
-Would be my first vape that uses a glass stem. I assume you put the herb on the underside of the honeycomb screen?
-FC discount?
-Any risk of any gunk getting onto the heating element and causing a problem?
I've made a few videos showing how to use the ENano...

- a really small amount.. I use about 0.05-ish gr for a full load... less, usually
- yes. I have a video demonstrating how I do that...
- The temp dial goes up to 11. I usually use mine at about 6.25. there are marks for each half.
- The herb goes in the shorter end of the stem. The EPIC that comes with it has a handy guide to show how deep the screen should be, and how deep the heater port extends into the stem. Fill the space between and you are good.
- FCLOVE
- I often get stuff "stuck" on the heater port screen. it brushes/blows/burns off, and the ENano is fine. No harm done. Load less next time.

Enjoy! :)
 

FlyingLow

Team NO SLEEP!
Working my way back into FC after a few months off after an injury, and find I am 40 pages behind in the Nano thread! Whoa you all move quick!


Nano is still performing flawlessly, never any problems with the device.
I use Ed's stem the most, without C-clip to improve airflow and decrease resistance and clogging.

I really like the way my glass stems and JODA glass pulls as well- but I am seeking advice on how to keep the basket screens in place?? I get real frustrated the screen always moves and seems to be a different distance from the heating element on every pull. What can I do to keep them in place and from moving up and down the stem? I often take the screen out, open it up a bit (widen), and reinsert, but it moves down with every stir after each hit... really annoying when trying to use Joda steamroller as I cannot just poke it back up from the underside, and often trying to pinch it from the top occasionally dumps the basket out inside the pipe. There has to be a solution!
 

Enchantre

Oil Painter
Working my way back into FC after a few months off after an injury, and find I am 40 pages behind in the Nano thread! Whoa you all move quick!


Nano is still performing flawlessly, never any problems with the device.
I use Ed's stem the most, without C-clip to improve airflow and decrease resistance and clogging.

I really like the way my glass stems and JODA glass pulls as well- but I am seeking advice on how to keep the basket screens in place?? I get real frustrated the screen always moves and seems to be a different distance from the heating element on every pull. What can I do to keep them in place and from moving up and down the stem? I often take the screen out, open it up a bit (widen), and reinsert, but it moves down with every stir after each hit... really annoying when trying to use Joda steamroller as I cannot just poke it back up from the underside, and often trying to pinch it from the top occasionally dumps the basket out inside the pipe. There has to be a solution!
A dirty screen is your friend here...

Put a fine bead of errrl/concentrate/reclaim around the basket bottom/top edge, perhaps after you have it positioned perfectly, and let it kinda set up and seal it in place. Leave it in place when you clean, too... I think mine CAN'T move at this point, even after PBW! :)
 

OnCloud8

Vapor Vixen
wow! first combustion event with the Nano tonight. Damn, left it on 10, hit it, and instant orange in the GonG, yikes! pulled the nano and it went out, sheesh...ISO FOR ALL THE PARTS!

I'm assuming this is generally not a big deal though right? I've seen plenty of people report similar events and its not like the Nano needs to be replaced or repaired now does it?. All looks normal with the heating element, outside and inside (as well as I can see in there!). Sooo....clean up and carry on vaping, yeah?
 

ACE OF VAPE

Vape outside the box
Manufacturer
smr3hh.jpg

Yes, you can remotely control your E-Nano with this setup! I picked it up at HomeDepot for $59.
The center button on the remote will remember your favorite temp. If you buy the Lutron 'Bridge' accessory you can control your E-Nano with an app on your phone! Once you set your favorite temp on the remote you don't even need the temp controller on the E-Nano cord so you can use any standard non-polarized ac cord.
 

Delta3DStudios

Well-Known Member
Accessory Maker
I'm assuming this is generally not a big deal though right? I've seen plenty of people report similar events and its not like the Nano needs to be replaced or repaired now does it?. All looks normal with the heating element, outside and inside (as well as I can see in there!). Sooo....clean up and carry on vaping, yeah?

No, your glass is ruined. It's been tainted by the evil combustion. Destroy it immediately and buy some new stuff :science:

Edit.... Kidding Of course! But seriously, when that happens, I usually can't get over the taste for the next few hits, no matter how much ISO I use :puke:
Fortunately the combustion taste seems to fade pretty fast
 
Last edited by a moderator:

421

Well-Known Member
smr3hh.jpg

Yes, you can remotely control your E-Nano with this setup! I picked it up at HomeDepot for $59.
The center button on the remote will remember your favorite temp. If you buy the Lutron 'Bridge' accessory you can control your E-Nano with an app on your phone! Once you set your favorite temp on the remote you don't even need the temp controller on the E-Nano cord so you can use any standard non-polarized ac cord.

Awesome that this works! How many steps of temperature control does the remote give?
 

flotntoke

thoroughly vaped
Im heavily considering picking up an E-Nano after my thread in ask FC, so i figure for more specific info i'd come here. Currently torn between the E-Nano and Arizer extreme Q.

Just a few questions to E-Nano owners (Or the manufacturer).
-How much can be loaded into the E-Nano?
-Can it be used with concentrates, both hard and oils?
-Does the VVPS show you what temperature/ have temp markers on it?
-Would be my first vape that uses a glass stem. I assume you put the herb on the underside of the honeycomb screen?
-FC discount?
-Any risk of any gunk getting onto the heating element and causing a problem?


If you're not sold yet (and you should be! ;)), let us know. I've had my EQ for more than 4 years. It's an OK vape. But, has only been out for about 10 days (while my nano was out for refit/repairs) since I got my nano 2 years ago. And franklr, that was kind of painful. Unless you're really anxious to fill bags (a novelty that seems to die quickly for almost all), the nano is a much better experience.
 

Poostuff

Please delete
I used to combust accidently all the time when I first got my mine, so much so that people started to call me Captain Combustalot (ok I made that bit up) but seriously it's always user error. Too tight pack with slow draw can be a problem. I'm all sorted now.
Also I LOVE that idea @ACE OF VAPE I'm so going to look into that & see if it's possible with a stepdown. Cheers.
 

Tweak

T\/\/34|<
smr3hh.jpg

Yes, you can remotely control your E-Nano with this setup! I picked it up at HomeDepot for $59.
The center button on the remote will remember your favorite temp. If you buy the Lutron 'Bridge' accessory you can control your E-Nano with an app on your phone! Once you set your favorite temp on the remote you don't even need the temp controller on the E-Nano cord so you can use any standard non-polarized ac cord.

Awesome.

I'm guessing this will work with the older style unattachable power cables? Just leave it on 10 and let the Lutron dimmer do the dimming?
 

SSVUN~YAH

You Must Unlearn, What You Have Learned...
Hey guys, I mainly lurk here, but if there's anyone reading who was thinking about buying an E-nano and hasn't yet, it's on Massdrop for a pretty good price.
Just a heads up Massdrop will only save you around $5-$10 typically per item and shipping is worst than waitng for China equipment IME. If you don't want a long drawn out MD process to save a ten spot or two, I really reccomend ordering straight from Epicvape, free lifetime warranty and not having to wait forever on MD with their excuses. With code "FCLOVE" you get 10% off and will get your Nano in less than a week!
 
Last edited:

*plainlazy*

Well-Known Member
Sucks ain't the word. Lend stuff to friends and get it back broken :-(

Also it's second hand enano from the sale page here. And I'm in the UK so shipping back and forth is gonna be time consuming. I've privately messaged ace of vape on here asking what the return process is or can he send me the part and ill fix it. I would prefer this.

Basically the power lead connection port is broken so the power lead plug doesn't fit snuggly and stay in the port. And one of the pins is rattling about.
 

*plainlazy*

Well-Known Member
Trying to find a 3rd party that can provide the socket part to fix it my self but can't seem to track down the exact fitting socket.
Can blag rubber or cork feet from anywhere.

I'll wait to see what andy/ace of vape says.

Back to the solo :-(
 
Top Bottom