JoDa Glassworks

rat949

Well-Known Member
Manufacturer
Well I still don't have the pieces in hand, but I got a photo of my steamroller and gong for my solo and I'm looking very, very forward to trying them out!

gg3FkY4.jpg


Thanks a ton!
 

ChippyMalone

Be here now.
Accessory Maker

Ha! I just found this photo and realized this is the exact one you sold me last week. I love it.

I've got another Koa wood E-Nano on the way and was thinking my wife might want to buy me some nice glass from you for Christmas.

I'm going through this thread to find ideas for what I want, but I am imagining a Hawaiian lava theme. Maybe a stem with bumpy black texture and glowing orange/red lava oozing out? Does that give you any ideas?
 

herbivore21

Well-Known Member
@VaPeD&CoNfUsEd

I am looking to get someone to make me a boro (or if required, quartz) adapter to connect my sublimator heater directly to my oil rig. This heater gets hot, and is a chunk of titanium - as such, it would be good to have a little bit of space between the boro directly touching the heater and the boro directly touching the piece so as not to put too much heat into my oil rig. It will need to have a female 18mm GonG joint on it to connect to my 18mm male di oil rig.

I will not be leaving the heater on top of this all the time, but it will need to withstand the heater sitting on it while I take a dab. The boro connection to the sub will have to be well molded to the shape of the dabmaster heater so that the heater sits in a firm and secure way in the adapter. I can't have a heater falling out of it's receptacle whilst dabbing lol.

Do you think you can do this? I will need super thick, super strong glass. I'd love to get some worked stuff done on it, but not if it compromises the function of a sturdy joint to connect my sub heater directly to oil rig for dabs.

By the way, long time no speak around these parts, hope all is well!! :D

Here is a picture of me doing what I want to do but using a clumsy 18mm f-f adapter with an 18mm combustion slide (The slide is not a good solution because the heater must be held in place with one hand! The shape of the inside where the sub heater sits is smooth, curved glass which makes the sub not sit snug and fall out!):

KiPKl6x.jpg


Ideally, I would want the heater to be connecting lower down, around the height of the middle joint on the 18mm f-f adapter as pictured. Please let me know if you could help me here and how best to get the measurements required :D
 

VaPeD&CoNfUsEd

JoDa Glassworks
Glass Blower
Honestly bud, I may not be the guy for that job yet. I'd almost have to have the sub to be able to make sure I had a good fit before shipping. Sure would be nice if it was the same size as an 18mm joint or something. That'd make shit a lot easier.
 

herbivore21

Well-Known Member
Hmmmm, the sub heater would fit pretty snug in a slightly bigger than 18mm female gong joint. In fact, the atomizer that the sub heater sits in during normal operation is a 25mm female joint.

I actually may have access to a 3d scanner which could give us exact dimensions. I wonder if there is some way I could give this information to you? I am sure boro will be just fine, this slide works; only it doesn't hold the sub heater in place - it is just not deep enough so the heater tips out.
 

Reflections

Well-Known Member
ok some pics of my bad ass stem Joda just made me...sorry not real clear pics..just had my pc camera

339ht2w.jpg


r8toie.jpg


r8toie.jpg


2yv2phx.jpg


2d7iww7.jpg


and a couple of my aromatherapy cup.. I havent tried it yet but will let yano how well it works when I can

2qd955i.jpg


t5pyxc.jpg


2mo9ykk.jpg


Sorry if to many pics :D I love both !!! Thanks so much Joda for the excellant pieces!!!
 
Top Bottom