Discontinued The Persei Vaporizer for herbs and concentrates.

Fishbaitz

New Member
I have been looking everywhere on a manual or instructions to install my knibbler XL but i cant get it to pull through the smoke it works when i take it off but not when its connected help!does it just take way longer to heat up??
 
Last edited:
Fishbaitz,

kindbeats

Terps Up, Temps Down
I have been looking everywhere on a manual or instructions to install my knibbler XL but i cant get it to pull through the smoke it works when i take it off but not when its connected help!does it just take way longer to heat up??

The issue is that the o-ring on your Hercules cap isn't creating a seal with the Nibbler XL. The solution is to use the thicker o-ring on the cap and then use vaseline around the ring to help make a seal. I've run into this problem many a time as have others so, you're not alone.
 

Noize23

Active Member
BTW my V3R top had the evil "blinkenlights" too.

I have the same problem,always blinkenlights when i use the core with Kiss cards.....
i switched to batterys and v1 Top :)

What new features does the v4 top ?

Will it be the 8 again for sale?

thx forward
 
Noize23,

StormyPinkness

Rhymenocerous ʕ•ᴥ•ʔ
Also my last newb ? How long is to
Long for holding the button on a 3.7 cart? I feel like it doesn't really start baking good until 7+ seconds in. Maybe I'll time it

I do a little bb then roll it a little so it's more snakey and lay it on the coil. I usually hit the button a little to get it melting into the wick. How many hits I get depends on what I'm using and how clean/old the coil is, some of them give me 3-4 good ones and some give me like 10+ ones. But for 3.7 I do a method someone on here talked about. 3 seconds with the button pressed, 3 off, 3 on, then 3-ish depending on vapor and whether you want to cool it. I used to do 5-6 seconds with the button on and I'm much happier this way. The wax in the cup just get's scooped up with a toothpick or something non-metal and just put it on the coil to vape.
 
StormyPinkness,
  • Like
Reactions: Vape Dr.

spoutti

Well-Known Member
Tx @DaNi_DuB for explaining me what was happening with the protection circuit thing. I dont understand how it works, but I think I found a solution for my persei to work with 7.4v and 3.7v flawlessly. I tried the hypothesis that this circuit didnt like voltage swings. No more voltage adjusting on the core ----> always accept my 3.7v carts for the last 3 nights with core and batteries!
 

k3nd4l

Well-Known Member
I do apologize guys the move has things all messed up and either today or tomorrow we should be 99%


As for the v4 tops almost done with production parts as they number in the thousands and assembly should start I think not this coming Friday but next.

any word on sr74 restock ?
 
k3nd4l,

TommydCat

Well-Known Member
Recommendation for those of us not having issues with the original button? Should we eventually swap 'em out as well? (I'll pay for shipping when you get more Nibbler XLs in ;))
 
TommydCat,
  • Like
Reactions: Vape Dr.

THC SCIENTIFIC

To Boldly Go Where No One Has Gone Before
Manufacturer
Will the 8 be relisted once you get the buttons in?

yes
Recommendation for those of us not having issues with the original button? Should we eventually swap 'em out as well? (I'll pay for shipping when you get more Nibbler XLs in ;))

Up to you doesnt hurt to have the spare assembly.
 

itschad

Well-Known Member
Same, I got mine in today as well @DieHard !


Trying to decide if i wanna swap out the bottom threads from my 74 as it's got the o-ring slots for the nibbler

people still having issues with the 74 adapter on the 8?
 
itschad,

konmo

Active Member
Same, I got mine in today as well @DieHard !


Trying to decide if i wanna swap out the bottom threads from my 74 as it's got the o-ring slots for the nibbler

people still having issues with the 74 adapter on the 8?
I got my sr71 yesterday. So far I'm liking it better than my 74. Heat up times are much faster and it seems to fire all the time. I'm already using the new button assembly.

I was having problems with the sr74 bottom adapter so I ordered a 71 type of adapter, but this one still has grooves for the O rings.
 

spoutti

Well-Known Member
Im starting to understand more the feel of vaping oils. I filled my kiss 7.4v with like 0.1g of concentrate and managed to keep the taste good and vapor smooth for a while. A first for me. I was under the impression that a filled kiss cup was easier to not over press the fire button keep getting smooth good tasting clouds. Untill I fired too long and got a huge harsh hot knives tasting cloud...

Im looking to buy a meter to gage my battery levels. I want to study how quick and what numbers pleases me.

Do I need the expensive capacity meter like this? http://www.ebay.ca/itm/Capacity-Tes...831?pt=US_Battery_Testers&hash=item3cda7b69af

Or a simple voltage meter should do? http://www.ebay.ca/itm/Blue-LED-Pan...y-Digital-Voltmeter-DC-3-3V-30V-/130704824376

I dont really know much about li-ion maintenance, but I was surprised to read an 18650 gives 4.2v at full charge. I thought it started at 3.7v and went down from there. Tips and pointers are all well appreciated :)
 

lockie

Well-Known Member
I think if you get a "huge harsh hot knives tasting cloud" you probably held the button down too long and got some wax in your mouth. At least in my experience.. Keep calm, spit and carry on sir.
 

spoutti

Well-Known Member
Tx for relating. The thing is I feel I have to give that extra button push to finish whats in the bottom of my ceramic cup. The way I see it atm is I kept the hard leaning on the button for the end of the cup. Specially before I put another kind of concentrate.

Im still expermenting :)
edit: I should say white cup. I dont really know what its made of
I think if you get a "huge harsh hot knives tasting cloud" you probably held the button down too long and got some wax in your mouth. At least in my experience.. Keep calm, spit and carry on sir.
 
spoutti,

invisiblefriend

Well-Known Member
Manufacturer
uh oh ----- not just blinking :(

@THC SCIENTIFIC --- today I decided to try batteries since the core is on the fritz a bit....( i put a ticket in recently but no reply yet -- n i just checked and do not see the ticket any longer ??? )


but today I tried my sr-74 with my v3 top / batteries ---- I pressed button -- and of course it blinked n blinked -- then it worked for a few seconds and blinked again ---

now it will not do anything but blink ??? no power going through it seems at all? it just blinks every time it is pushed --

I put it on the core and same deal blinking -- no solid button even with zero cartridge on top ?
(sounding bad ? :( )

i have the old hammer top n it woks -- so it must be the silver v3 top ? and unfortunately the core (which I know is the connection going into the bottom of the core top .... ) since i can only work it when I fool around with it --

suggestions my friend

or should it get sent in ?

thx for advice and help my friend ? -- I purchased in July 4 my B-day .... the core and the silver top ...


I checked the site -- n i cannot find ticket section ... --

I sent a msg on oct 28th re the core problem ... (under my account -- kindcorp@gmail.com)

but now its the Persei top as well :( b4 the weekend too :( uh ohhhh ....


what are my next steps my friends ?

thank u in advance !


ok ok ok ---- trying to troubleshoot ---

and how about this -- its not off >??????? it won't stop working ????? not safe now .....
I guess --
since I use the hercules .... i didn't realize till now ..... since it takes some time to heat up rod

i am using the 3.7v herc rod --- and was when this happened -- w/blinking n all n i thought it wasn't working at all ?? a little of the opposite ?

i just tried some extra testing -- using a kiss globe coil system and to my surprise after I screwed it in it started pumping out voltage / vapor if it was loaded / getting hot --- even with the silver top off -- if I hit 5 times and turn off -- the light shows off but it keeps running off or on -- just no way to shut it off -- and the light only blinks and never will stay solid -- but if battery inside it will not stop pushing power ??


very odd ?
any ideas my friend ...

ill stop here till I hear from you ?

thx in advance
doesn't seem gd 4 me :(

i miss her already :(
 
Last edited:
invisiblefriend,

StormyPinkness

Rhymenocerous ʕ•ᴥ•ʔ
Wanted to try a 7.4v cartridge in my okeanos and it wouldn't screw all the way in. My ti2 3.7v cart has the same issue. Only the one that came with it and the my ti1 cart seem to fit. Not expecting someone to have a fix for this, just hoping. I was going to order a backup 7.4v kiss soon anyways, hopefully that one will fit. Just waiting for the boro globe glass to be in stock.
 
StormyPinkness,

Nube Scrutator

Cloud Searcher...
The Persei Armatura!

389851F6-4625-466F-8813-49760E4C833A_zps8jwefimg.jpg

736FC987-F847-407E-9887-CE2E05B57A7C_zpsrq7x80mh.jpg

44B35BDA-FC82-4ECC-BAE4-837059456EEA_zpspdgahw28.jpg
 

invisiblefriend

Well-Known Member
Manufacturer
hmm -- tryin to figure out the exact pieces :)


pretty setup -- no doubt my friend --



do I need to talk to w9 b4 I send in 4 repairs ---- I'm scared without my Persei :)
Im sure ill here from @THC SCIENTIFIC any minute --- but i was surprised i haven't heard from the site since last week -- and no one on the phones ---
if I was in cali -- id drive it in :)

peace
 
Last edited:
invisiblefriend,

THC SCIENTIFIC

To Boldly Go Where No One Has Gone Before
Manufacturer
Sorry guys running around getting the last pieces of the puzzle in place so we are good to go on the 8's on Monday.


Also for repairs submit a ticket or send the items in to the address on the website under shipping and returns along with a note saying what's wrong and copies of your reciepts, along with your contact info.


510 globes both for mods and egos are in stock, and Minicron lites as well.

Don't forget 8's start shipping again on Monday.
 
Top Bottom