next generation e-nails?

i love you mary

New Member
so whats the consensus on the best e-nail for the best price?

what happened to hive? they were/are supposed to release an e-nail.

anyone tried or purchased the hgh e-nail?
 
i love you mary,

Deadshort480

We're here to fuck shit up.
There is no best. As it has been stated already, most if these Enails are all similar with small differences. The market is literally flooded with them right now. Basically, just choose a manufacturer that you've heard good things about.
 

hanfhead

is high
can you recommend a site for all the supplies?

i want to use a ceramic nail. temps from ambient room to 1200.

thks.

I think this guide has the most complete list of parts.
http://www.reddit.com/r/CannabisExtracts/comments/1kczbg/diy_enail_howto/

Read through the comments there for how to program the pid and what settings work best. Make sure to get 5 pin xlr connectors. The only soldering required is to put the xlr connector plug on the coil and connection from the relay and temp sensor on the inside of the box to the xlr socket. I don't know about using ceramic for an enail, I have seen it done but don't have any experience with it. Someone here can probably help you or check out the enail subreddit http://www.reddit.com/r/enail/
 

i love you mary

New Member
I think this guide has the most complete list of parts.
http://www.reddit.com/r/CannabisExtracts/comments/1kczbg/diy_enail_howto/

Read through the comments there for how to program the pid and what settings work best. Make sure to get 5 pin xlr connectors. The only soldering required is to put the xlr connector plug on the coil and connection from the relay and temp sensor on the inside of the box to the xlr socket. I don't know about using ceramic for an enail, I have seen it done but don't have any experience with it. Someone here can probably help you or check out the enail subreddit http://www.reddit.com/r/enail/

thank you!
its appreciated.
 
i love you mary,
  • Like
Reactions: hanfhead

Caligula

Maximus
FWIW I dab at between 600 and 700°F


edit: I suppose being able to get it to red hot would help in cleaning the nail.
 
Last edited:
Caligula,

violentz313

Well-Known Member
Just thought I would mention that there the guy at Domeless.com has made another more simple ceramic coil e-nail.

The 710 whip

http://www.domeless.com/products/?full_only=true#category=710-whip

All this for $100!

p2inuLr.jpg


http://iconosquare.com/p/762630757324448369_931506815

I haven't used one nor do I work for the company, just wanted to share :)

Just put my order in will report back some time in august. Its only $100 so I figured what do I got to lose ill be a guinea pig lol
 

PhotoRider

Diagnosed with level 11 G.A.S.
Just for fun, I built a dual e-nail setup using the standard design and the MYPIN TA4 PIDs and the new XLR connector. Got the programing done and its working nearly as good as my D-nail original unit.

Going to build a triple for my buddy's dab bar where we hang alot. Nice glass bar in a semicircle made out of glass. Figure setting up three stations with complete control would help avoid passing pieces around. Also, easy to compare nail step-ups or even different glass itself. Typically run a 20mm dish, 18mm female quartz nail on one rig and a Omni nail from Santa Crus Shredder using a 10mm coil and the standard D-nail base. Tried out the original rev 1.1 TI nail (10mm coil) and the new 20mm dish rev 1.2 TI. For TI nail use the Omni nail is the best so far. Just bought the top section from SCS and use the original D-nail base and coil. Also bought the new rev 1.2 top since I use a 20mm coil on the quartz. About $450 out of pocket with coils and 2 nails.

Also bought the cheaper coils from AliExpress.com. Comes pre-wired with the XLR male plug wired compatible to the production D-nail XLR female panel connector. Only $60 ea. Uses the same sleeve etc. only thing takes time to get and shipping is a bit high. $16, then $6 for each additional.

Dual_D-nail-1.jpg
Dual_D-nail-2.jpg
 
Last edited:

amberevil

Well-Known Member
On their site it says 150, is there some kind of promo code? I cant wait till you share your product review.
 
amberevil,

215z

Well-Known Member
Hi @amberevil good catch. It used to be $70 for the heating element, or $100 bundled with a $30 nail.

Now they list the heater for $75, as well as a $150 bundle that includes the $30 nail as well as a $25 carb cap and a soft carrying case.

I hope to see a review of this soon!
 
215z,

Caligula

Maximus
Just for fun, I built a dual e-nail setup using the standard design and the MYPIN TA4 PIDs and the new XLR connector. Got the programing done and its working nearly as good as my D-nail original unit.

Going to build a triple for my buddy's dab bar where we hang alot. Nice glass bar in a semicircle made out of glass. Figure setting up three stations with complete control would help avoid passing pieces around. Also, easy to compare nail step-ups or even different glass itself. Typically run a 20mm dish, 18mm female quartz nail on one rig and a Omni nail from Santa Crus Shredder using a 10mm coil and the standard D-nail base. Tried out the original rev 1.1 TI nail (10mm coil) and the new 20mm dish rev 1.2 TI. For TI nail use the Omni nail is the best so far. Just bought the top section from SCS and use the original D-nail base and coil. Also bought the new rev 1.2 top since I use a 20mm coil on the quartz. About $450 out of pocket with coils and 2 nails.

Also bought the cheaper coils from AliExpress.com. Comes pre-wired with the XLR male plug wired compatible to the production D-nail XLR female panel connector. Only $60 ea. Uses the same sleeve etc. only thing takes time to get and shipping is a bit high. $16, then $6 for each additional.

Dual_D-nail-1.jpg
Dual_D-nail-2.jpg

So how's this thing holding up @PhotoRider? Interested in doing a project like this however I'm more interested in a single coil unit.

@215z what's this $150 unit you're talking about?
 
Caligula,
  • Like
Reactions: farscaper

amberevil

Well-Known Member
It just sounds to good to be true. I want to go e nail sence reading this thread. I just want to save my money. I currently dab on titanium but dont have my mind set one way or another. From many posts ive read here about different nail materials, it seems they each just have there own pros and cons. But low temp enails for sure, and a carb cap. Ive never even used a carb cap.
 
amberevil,
  • Like
Reactions: Caligula

Radio

stay true to yourselves
Just for fun, I built a dual e-nail setup using the standard design and the MYPIN TA4 PIDs and the new XLR connector. Got the programing done and its working nearly as good as my D-nail original unit.

Going to build a triple for my buddy's dab bar where we hang alot. Nice glass bar in a semicircle made out of glass. Figure setting up three stations with complete control would help avoid passing pieces around. Also, easy to compare nail step-ups or even different glass itself. Typically run a 20mm dish, 18mm female quartz nail on one rig and a Omni nail from Santa Crus Shredder using a 10mm coil and the standard D-nail base. Tried out the original rev 1.1 TI nail (10mm coil) and the new 20mm dish rev 1.2 TI. For TI nail use the Omni nail is the best so far. Just bought the top section from SCS and use the original D-nail base and coil. Also bought the new rev 1.2 top since I use a 20mm coil on the quartz. About $450 out of pocket with coils and 2 nails.

Also bought the cheaper coils from AliExpress.com. Comes pre-wired with the XLR male plug wired compatible to the production D-nail XLR female panel connector. Only $60 ea. Uses the same sleeve etc. only thing takes time to get and shipping is a bit high. $16, then $6 for each additional.

Dual_D-nail-1.jpg
Dual_D-nail-2.jpg
Insane collection there! What a high-tech setup to be proud of :)
 
Radio,

PhotoRider

Diagnosed with level 11 G.A.S.
So how's this thing holding up @PhotoRider? Interested in doing a project like this however I'm more interested in a single coil unit.

@215z what's this $150 unit you're talking about?

Well, have not used my old dnail since I built this dual. Unless a component fails, not much to go wrong really.

The secret sauce is the PID values and stability from them. Dnail locks you out of that area on their menu, maybe your values are not as precise, but they work very well.
 
PhotoRider,
  • Like
Reactions: Caligula
Top Bottom