masaki
Well-Known Member
Did you try torching it?
Discontinued The Persei Vaporizer for herbs and concentrates.
- Thread starter THC SCIENTIFIC
- Start date
Did you try torching it?
syrupy
Authorized Buyer
Well both those accessories are heavy hitters, and would benefit from a steady stream of power that the core is designed to deliver. From using the hercules, I know when the batteries lose enough juice, it performs poorly. More than once, I took herc apart after getting wispy hits, only to find it was just that the batteries had discharged too much to give enough juice that behemoths like herc and the hammer require. I think the new tops blink when the batteries get low. Of course with the core, that never happens.
Edit: I just sold myself on the core.
You just take a torch to it and thats all? Because no.
I want a core because i kill batteries like nobody's business
masaki
Well-Known Member
I don't own a torch or any lighters lol but I've read people doing it on this thread. What I do is dry burn my white rod without the coil inside the herc and it burns all the black shit off.
First just replace it in there, remove outer shell, mouthpiece, airflow cap, and coil. Then just hold the button and cook it for 20 seconds at a time until white. If that fails after a few tries, remove rod and slide a small penknife blade gently down the side and try again.
Had an issue with low grade wax ONCE. Learned my lesson. Had the same issue then as you do now.
Hmm suddenly i am unable to get the herc itself (inner part, no bottom insulator or outer shell) to register anything under about 6 ohms. i tried to pull out the ceramic rod for cleaning, it's stuck in there pretty well so i guess i will have to break out the torch tomorrow 
it doesn't look like the rod should though i think....
ill get a better pic tomorrow when the rod is removed but i t looks like there is a good size split down the middle i dont remember
it doesn't look like the rod should though i think....
ill get a better pic tomorrow when the rod is removed but i t looks like there is a good size split down the middle i dont remember
bellas
Well-Known Member
The Core comes with a booklet I think it states you can run the Herc. up to 7.5. I have played around with different temps and have been pretty happy at 7.0. I am using the Core/Herc/Bender strictly. I was ready to drop the Bender until I got the Core. I just hated the Battery issues. I could not ever be sure that my batteries were going to run consistently enough to warrant a comfortable relationship with my vape. I have three sets of batteries and smoke pretty heavy. I was finding that I could get one really good session per battery change. Thats definately not enough batteries for my needs. I wanted the Bender strictly for home use and with the Core I have finally got that.
Bleed4Me
I LURK
Hmm suddenly i am unable to get the herc itself (inner part, no bottom insulator or outer shell) to register anything under about 6 ohms. i tried to pull out the ceramic rod for cleaning, it's stuck in there pretty well so i guess i will have to break out the torch tomorrow
it doesn't look like the rod should though i think....
ill get a better pic tomorrow when the rod is removed but i t looks like there is a good size split down the middle i dont remember
Heat it up a little and push it up from the bottom. If you pull it out through the bottom, all the black shit in the rod will scrape off in to the bottom of the cart and you will have a burnt taste right after you torch your ceramic. If you have it all apart, might as well give it a clean up...
Good luck!
Caligula
Maximus
Exactly. Push don't pull. And yes that groove down the side is normal.
@exit darb is right ...push the rod out from he bottom. Also groove down the side is part of the design. No worries. Try checking herc assembly for ohm issue. Barring that, ask THC to Skype you.
Edit....just saw Caligula and bleeds responses too... spot on.
Vapoholic420
-Loyal To The Oil-
Does anyone know the exact specs of the o-rings for the Nibbler XL? I asked a page or two back but no-one has replied. I want to order some replacements and they come in bags of 100 where i found them online, so I want to make sure I get the right size the first time. But I'm not sure how to measure them, so if THC Scientific or anyone else could help, please let me know. Thanks in advance.
DatOilVape
Member
Is a core v2 coming out anytime soon, i want to get a core hella bad.
Caligula
Maximus
No. Its not.
DatOilVape
Member
So i can buy one today and feel comfortable that an upgraded version isnt coming out in next two months? And the bubler tank vs sr-74 what do you guys think
Last edited:
Keep us posted, or I'll be all curious! Lolrod came right out for cleaning. heres hoping a cleaning will bring it back to life
=)
Good luck!
MileHighLife
Blower of glass, grower of grass
No lo veo
Bleed4Me
I LURK
Got my Core today and decided to take er out for a spin =]
@THC SCIENTIFIC My core is making a very quiet buzzing sound, is this normal?? I dont want it to become louder ]=
Normal. Mine does the same. It's purring...
TommydCat
Well-Known Member
Mine does as well and changes tune when you hit the button. Judicious changing the voltage and I think we might be able to play a tune!
DatOilVape
Member
So what you think is the core worth it?Got my Core today and decided to take er out for a spin
Fixed
masaki
Well-Known Member
Ya for sure now I dont have to worry about my batteries dying on me when Im out doing shit and if I need to cut loose I got a fully charged batteries ready! As for function I haven't gotten the chance to fully test it out, I want to see how the bender performs and the black rod at 4v
I will get you the info tomorrow soon as i get in the office.