Discontinued The Inhalater INH004 Phytotherapeutic Rechargeable Portable Vaporizer
- Thread starter Dogman
- Start date
Vaporisateur
Senior Marijuanist
1) Grass only.
2) You should clarify with the vendor, it should be either or.
2) You should clarify with the vendor, it should be either or.
Dreamerr
Always in a state of confusion and silliness♀
First off you are in the wrong thread for the xp... http://fuckcombustion.com/threads/inhalater-xp.8386/page-36#post-353606
Secondly I have used kief in a sandwich only but I am with vaporisateur ask the manufacturer. If stuff gets below that bottom screen it can be the end of your vaporizer.
VapeNStone
Mark
Well my inhalater is gone 
But I'll have an XP as it's replacement 
But I'll have an XP as it's replacement ![:\](/i/s/hmm.gif "Hmm :\")
VapeNStone
Mark
mine was working great, but I had a forced tolerance break for 4 months. So it was just sitting collecting dust. So I'm assuming whatever happened was because of that? IDK. It also had the dim issue.
Plug it in for at least 24 hours straight if you haven't already. The battery might have dropped so low over time that the circuit just isn't picking it up. In any case, the terminals will still have a very tiny amount of power going to them, so it will trickle charge and over a while (hopefully) spring back to life.
VapeNStone
Mark
Naw ID believe that to be the problem. Because when I plugged it in the charge light would come on for a milla second and then lose connection or something.
AdmiralAlpacha
Well-Known Member
In the XP thread it is advised not to have the unit on max temp without a capsule in it. Does this apply to the regular inhalater as well?
AdmiralAlpacha
Well-Known Member
I have done it probably 4 times in the past in order to try to burn off any residue in the bottom screen. Seeing as my inhalater is still running pheneomoley I dont see how it could have negatively affected it (also with the thicker polyimide I don't think we need to worry) but I figured I would ask before continuing.
It is awfully hard to reach down into the air holes where some wandhash can develop and clog intake, turning onto max temperature seems to help this (or i'd guess based on the visible vapor produced from doing so.)
Apologies for sentence structure and spelling, celebrating my birthday tonight
Vitolo
Vaporist
I always plucked the inner screen out to clean with Iso.
It is easy and done with any stir tool.
I have new replacement screens also, but never needed them....
...becauses I found that after each load if I use the little plastic straw, I could suck out any stuck debris.
Heating any thermostatic controlled device with it's door open will reduce it's life expectancy.
It is easy and done with any stir tool.
I have new replacement screens also, but never needed them....
...becauses I found that after each load if I use the little plastic straw, I could suck out any stuck debris.
Heating any thermostatic controlled device with it's door open will reduce it's life expectancy.
Vaporisateur
Senior Marijuanist
Any way to get the screen out from the heating chamber?
AdmiralAlpacha
Well-Known Member
using a stirring tool, paperclip, or anything small that you can kind of hook under the screen with, and then it pulls straight out. It took me awhile to get it, but it can be done. I used a small paperclip, it worked but was a bit thicker than something ideal.
Vaporisateur
Senior Marijuanist
So I made a little video on how I use my Inh004. Yes, I still have the stickers - holding well too
Hope you like it
Hope you like it
CapitalFlower
Well-Known Member
Hey guys,
My Inhalater has broken on me and I'm trying to fix it.
Basically, it was plugged in charging, I must have pulled the cord out at a weird angle because now the charging jack has become loose, and won't charge.
Is there a way of taking it apart so I can have a look inside and try and fix it?
Many thanks!
My Inhalater has broken on me and I'm trying to fix it.
Basically, it was plugged in charging, I must have pulled the cord out at a weird angle because now the charging jack has become loose, and won't charge.
Is there a way of taking it apart so I can have a look inside and try and fix it?
Many thanks!
Vaporisateur
Senior Marijuanist
CapitalFlower
Well-Known Member
well seems as if I've just made it worse, my soldering iron is too big and I can't get it back on the board.
Anyone wanna buy a faulty inhalater? lol
Anyone wanna buy a faulty inhalater? lol
Vaporisateur
Senior Marijuanist
Blow up video for FULL HD 1080p