• Do NOT click on any vaporpedia.com links. The domain has been compromised and will attempt to infect your system. See https://fuckcombustion.com/threads/warning-vaporpedia-com-has-been-compromised.54960/.

Dabpress Rosin Plates

MegaMan2k

Well-Known Member
Cool thanks for reporting back hackerman,

Maybe this little thing could actually help lower my tolerance a bit xD

My m8 sold me a "E. Ross 4.0 enail" like 6-7 months ago, I cant really remember what has happend and was has not happend since that day.
 

BabyFacedFinster

Anything worth doing, is worth overdoing.
I hope this is on thread topic enough,
If you are like me, the sight of rosin left behind on the edge of a pressed puck glistening in the light makes me feel like I have missed a bit, even with over a 20% yield.
I just watched @ohmygodimsohigh (Troy) video on cleaning the new Boundless Terp Pen ($30 worth, how can they make stuff that cheap?) Almost at the end he describes how he likes to use the pen to bab straight off the edge of the bag, great idea, but I would say to do the little preheat to pick up the rosin so you do not get the nylon too hot. (handy for people like me that cannot be bothered with processing pucks):tup:
https://bndlstech.com/product/terp-pen/
These were on sale last week for $25, so shop around.:myday:

Edit; I really like mine, wish I had got 2 as @Hackerman says, pretty short battery life (long enough run times to do the job) but so convenient and hits hard.

To help keep things on topic, I'd add that the whole reason for buying anything related to rosin is because of my ability and enjoyment using my Dabpress. Now that I have the ability to press my own organic herb, I am always on the lookout for how to expand my enjoyment using rosin.

With that said, I was amazed by @LesPlenty's post, because he was watching the same video I was, probably about 3 days ago, and I also bought a terp pen (from PIU who has them for $25 right now) which should be here tomorrow.

I thought about getting the bits off a pressed, bagged puck but worried about melting the nylon.

BTW, I have done a lot of sampling between the wax I recently collected at 190F and the pull/snap that came from the same herb when pressed at 220F. While the wax was a very cool product and an easily usable form, the return was less and more importantly, I didn't notice a difference in flavor or effect between the rosin collected at the 2 different temps. I will test out this observation a few more times, but if I continue to notice little difference in flavor and effect between the two temps, then I'm going to stick with the 220F temp and get the most yield I can. There is always post-processing to mess with.
 

LesPlenty

Well-Known Member
Company Rep
I am finding the lighter colored, lower temp/pressure rosin to be a bit more flavorful and a lot cleaner on my Halo than the darker color, higher temp/pressure pull'n'snap and shatter to not quite have all the flavors, still good, just missing some of the lower temp crumble stuff. I think the darker rosin seemed to hit a bit harder though...more testing needed.:science:
 

Alexis

Well-Known Member
Hello guys. Long time not been here in this thread. So today I went to my friend Dave's house to sell him my 6T Bottlejack Dabpress after over a year idle, packed in a box.

I only ever did one single press, so I never actually got to practice and learn the ropes for myself and that was a year ago and I forgot pretty much everything I picked up in advance of my first press.

So I was really sketchy about going round there and passing on any and all knowledge and directions about pressing in general and the model itself.

I really wanted to give Dave a good idea to get him started but I wasn't able to be much help at all, partly due to having low brain power.

I gave him my slick paper (i hope you know which one I mean I bought it after it was recommended to me by one particular rosineer, before learning from several respectable members here and elsewhere that they cannot work with this one unless they use bags I think it was because it is too slippery ).

And I gave him all of the filter bags which I picked up with the press. This is where it was a bit tricky to give him any useful advice because I never practiced with the slick paper nor with straight nugs and no filter.

So I suggested he get some parchment paper, stick a 0.5 g nug in at 190 fir 2 mins to 2 mins 20 secs, and have a play.

But I promised him I would email him some Youtube links on the model, the bag tek and pre-press mold, and anything else to assist him.

So Im just looking on Youtube now at both Roger and @psychonaut 's channels (easy bro hope you are doing real good and still really appreciative of all of the advice and Direction you gave me last year).

So I will do my best to to shuffle useful and appropriate resources my friend's way but my brain is not very competent currently. So just reaching out in case I miss the obvious, or beat round the bush, if anybody has any no brainer links, vids or resources which sound like a suitable induction.....

I and Dave wouid really appreciate it. I feel a responsibility to try and help him out a little more because he works a hell of a lot and he is strictly not into forums otherwise I would just have directed him here.

But no importance I'm pretty sure we can figure all this out on our own just thought I would drop in case there is something useful I would otherwise miss.

Thanks guys, hope you all are doing well in life. Amazing herb we harvested again just recently. Lots more potent than ever before. Still recuperating from the hard work (for me anyway) of it.
:):tup:
 
Last edited:

pxl_jockey

Just a dude
@MegaMan2k wtf?! Just got raided?! I didn’t think shit like that happened anymore. Don’t the police have real crimes where you live? Is your house also a drug den? That’s just nuts, and while I am so glad your plates weren’t confiscated I gotta know what did they take? You seem fairly chill about it, is that sort of thing common? I would be losing my shit! You’re one cool melter-man!
 

DogBoy

know fear
...it's the real world after all...

...along those lines I have developed some complaints in regards to my '35v press...

...after noting how signifigent temperature is it occurred to me it might be a good Idea to see what the temperature of the plates actually were rather than just going by the settings and readings on the PID...

...it would seem the numbers on the PID are general indicators rather than actual values...

...they are off by 10 or 15 degrees...

...the values are not the same on both circuits even though the readings are...

...the top plate runs 5-7 degrees cooler than the lower plate at the same settings and readings...

...I have seen up to 15 degrees of variation in temperature in different areas of the plates surfaces as well...

...this can make it difficult and tedious to set a proper temperature...
 
Last edited:

MegaMan2k

Well-Known Member
@MegaMan2k wtf?! Just got raided?! I didn’t think shit like that happened anymore. Don’t the police have real crimes where you live? Is your house also a drug den? That’s just nuts, and while I am so glad your plates weren’t confiscated I gotta know what did they take? You seem fairly chill about it, is that sort of thing common? I would be losing my shit! You’re one cool melter-man!

They showed up because someone had reported me,
I only produce for my self and i dont sell, and the only reason i use is to deal with pain -.- and very few people know im into cannabis so its sadly someone close to me.

Im in Denmark so im kinda used to the 1800th century mindset around here, even tho its lame
Lost like 200-300 grams of dry herb guess they will report back with precise weight of my current stash-

Also there was 8 grams of rosin in the fridge they didnt even find,
and also a bag with 400grams of left over pucks that they didnt find either.

I dont have it in me to care about these low lifes tbh :D
 

LesPlenty

Well-Known Member
Company Rep
a good Idea to see what the temperature of the plates actually were rather than just going by the settings and readings on the PID
What are you using to measure your temps?
I had the same problem using a cheap K-Type thermometer, the wire probe delivered with most K-Types are that cheapo wire, I replaced mine with a hard nail type probe and my plates now read the same as my probe, IR guns can sometimes be put off by shiny plates too.:tup:

Also there was 8 grams of rosin in the fridge they didnt even find,
At least you weren't left 'Dry':tup:
 

psychonaut

Company Rep
Company Rep
@DogBoy had you made any adjustments to the configuration menu settings on the PID modules? The accuracy should be within 2-3% so at 200F this would be around 4-6F off at most.

Like @LesPlenty, I also recommend to use multiple thermometers to measure your plate temps. I have 3 that I use because my IR gun is the least accurate, but the other 2 show within 1-2F.

Also, be sure to measure your temps after the plates have had time to saturate, I recommend to wait for the set temp to settle for at least 5 minutes after reaching temps, before taking measurements.

Anyhow, if both plates are doing the same thing I would be suspicious of your thermometer, it is unlikely you have 2 defective PID modules, or 2 defective heating rods, or 2 defective thermocouples.
 

FlyingLow

Team NO SLEEP!
My temps were spot on (within 2-3*) when I last checked. Either your measuring instruments are off, or your temps are just out of calibration. If the later and you know your temp variation, simply accommodate for the variation and you should be able to dial in some consistent results.

@mega~ that is some scary shit! Production brings on all sorts of issues, even in the states [I wouldn't fuck with it outside of a legal state]. Glad you got off with just a wrist slap!
 

MegaMan2k

Well-Known Member
holy smokes it was more like 800 something grams confiscated just got off the phone with the police officer -.- Damn pucks, i hate you pucks , aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
 
MegaMan2k,

FlyingLow

Team NO SLEEP!
be very mindful of what you post. I don't know how your legal system works, but I'd refrain from posting anything incriminating until after your case is closed... It can get nasty when producing and with that amount, I'd be hopeful they do not attempt to hit you with distribution.
 

MegaMan2k

Well-Known Member
At this point it cant get any worse / they kinda got everything there was to come for and case is pretty much closed fallout is going to be a fine coming my way.
Luckily it takes quite abit to get charged with sales here :p but i def get ur point
 

DogBoy

know fear
...I chalked it up to limitations of the components and did not expect another unit to be any different...

...I assumed it was within parameters...

...currently have one set @ 210 and one at 215 to achieve approximately 200 degrees F...

...I am willing to accept that the especially high and low readings are from reflections...

...most of the readings are between 197 and 204 with the higher reading tending towards the plate set @ 210...

At this point it cant get any worse / they kinda got everything there was to come for and case is pretty much closed fallout is going to be a fine coming my way.
Luckily it takes quite abit to get charged with sales here :p but i def get ur point

...you are a cool bean...

...maybe it's not like they don't know but why print it out for them...???...

...when something like happened to me one time they missed the stash but still got enough to fuk us up some...
 
Last edited by a moderator:
Top Bottom