Ok here is some resin melting action 
Dynavap VapCap
- Thread starter Fenton Mewley
- Start date
Ramahs
Fucking Combustion (mostly) Since February 2017
Squiby
Well-Known Member
The lid is secured with a torx screw. I can't remember the exact size but it might be a #8 or 10. I have 3 Dynastashes and haven't had any trouble. If your screw loosens up a bit, you can tighten it up tighten it up with a torx screwdriver.
ElPic
Take my money
Hello all,
For people interested on a inexpensive 14mm water pipe adapter, I realized today that the Helix taster bowl from Grav fit perfectly with the Dynavap tips. On grav website it’s only 10$.
It’s long enough to heat the Cap without burning your finger.
Sorry if that have already been mention before!
For people interested on a inexpensive 14mm water pipe adapter, I realized today that the Helix taster bowl from Grav fit perfectly with the Dynavap tips. On grav website it’s only 10$.
It’s long enough to heat the Cap without burning your finger.
Sorry if that have already been mention before!
ataxian
PALE BLUE DOT
hoyo77
Well-Known Member
I have run hash thru mine with no issue...i have cleaned it a little more often when i have done hash.
KnutAnkhAmon
Tramp
I use hash with my Dynacoil. Earlier I used a pipe screen but the coil gives a much better taste.
The Dynavap is one of the best hash vaporizers I've tried.
The Dynavap is one of the best hash vaporizers I've tried.
3dfx-glide
Boats & Harbors
Ti tip and Ti CCD: if the screen is in the largest bowl position and you shake the vape a bit, does the screen come loose/rattle? Just wondering if it's supposed to stay in tight or if it being loose like this is normal and is just meant to be held in by herb
Dynalowrider
Well-Known Member
Take the screen out, lay it on a flat steel surface, (vice, truck bumper, anvil), hit it square with a flat faced hammer. Reinstall.
3dfx-glide
Boats & Harbors
Yeah tried, still loose on bottom and kind of finicky to get it to stay in the upper grooves too, got to take it in and out a few times each time
@3dfx-glide if you have torched the screen clean... That can shrink it in my experience.
I use the SS sreens myself as i find they last longer.
But both types of screen have their fans here on the forum.
I use the SS sreens myself as i find they last longer.
But both types of screen have their fans here on the forum.
Prophecy
Well-Known Member
From my experience I can say the cap itself is magnetic not only the clickers also the body from the normal M is magnetic but very weak but the body from the Shadow M is more responsive to magnets, I use on mine a 3mm diameter magnetic ball to cover the air port for use with a water piece works very good.
Last edited:
cybrguy
Putin is a War Criminal
I have never played with a Shadow M on a magnet, and after doing so I do see that there is an attraction, but it seems to be the coating and not really the steel. Both the black body and the black cap respond minimally to a magnet. Such is not the case for my 2017 M. Does your round magnet work on a 2017 or earlier M?
Prophecy
Well-Known Member
The more magnetic effect from the Shadow M is created by the coating process here the post from @VapCap
my Shadow M cap sticks very good to a dyna magnet with a little lower strength als the side who the clickers sit. I can test this with the magnet ball not with the 2017 M, I have given away my M 2017 and 2018 to a friend but to the 2018 M I can say that it sticks also to the body but very weak.
started@52
Well-Known Member
Brushed Nickel Magnetic Push Pins - (12 Pack) https://www.amazon.com/dp/B01LVW8945/ref=cm_sw_r_cp_api_i_4pbGCbWTK78TK
These things are great for everything, including the DV! I stash them everywhere, on my heaters, under a metallic lid, I even drilled a hole in one for my “Bud Pick”. You can remove a HOT cap before it clicks to check it or empty your cap, it pulls even stubborn(not stuck) caps off no problem. Not sure how they are magnetized but they work.
These things are great for everything, including the DV! I stash them everywhere, on my heaters, under a metallic lid, I even drilled a hole in one for my “Bud Pick”. You can remove a HOT cap before it clicks to check it or empty your cap, it pulls even stubborn(not stuck) caps off no problem. Not sure how they are magnetized but they work.
ataxian
PALE BLUE DOT
Hot tip!
in_human_form
Active Member
I'm considering the VapCap for traditional (moroccan) hash.
Isn't it easy to burn your hash with these torchlighters though ?
And how well can you clean the melted hash from this unit?
Isn't it easy to burn your hash with these torchlighters though ?
And how well can you clean the melted hash from this unit?
StringTheorista
Well-Known Member
https://www.marleynaturalshop.com/products/herb-and-roll-case
Has anyone tried one of these with a vapcap? I can’t find any interior dimensions online that would let me know whether a standard length vapcap would fit in the trench
Has anyone tried one of these with a vapcap? I can’t find any interior dimensions online that would let me know whether a standard length vapcap would fit in the trench
I only ever tried hash, well pollen, in my Vapcap a few times. I didn't tolerate the hash well. But from my memory and general understanding (at least I think), hash takes a higher temperature to vaporize than flower. I think it would be much harder to combust with hash in the vapcap. Im sure I was regularly going past the click, and never felt close to fire. I got better, more consistent hits actually, rarely harsh unless monster, which is much more doable with a full hash pack.
Saying that, a full pack wasn't anywhere needed to get clouds. Just crumbs would yield flower sized hits. Like I say, burning and combustion was never a fear. You aren't torching it directly, and flower is not burnt by the heat so no way hash will be easily either.
But alas there that one negative that you have brought up- cleaning. Hash=mess, gauze clogged quick. Inside of tip gummed up. If you can live with that it's all good.