Discontinued The Splinter by RBT

Status
Not open for further replies.

cybrguy

Putin is a War Criminal
Well, mine arrived. It is SO cute... Smaller than expected, but then so was the mod.

I'm trying really hard to wait until evening to try it out, but an afternoon appointment just cancelled...

Resist... or not.
 

AJS

Calm Consistency
Email from RBT today!

"Hey RBT nation... as promised this weeks specials on Milaana! ... and there just might be a few Splinter available too ;)

Maple Milaana will include an additional FREE - Battery, Charger, INTERPLANETARY small smell proof bag (provided by @TRDreviews)

Maple Milaana with exoitc cap will add an additional long mouthpiece and medium smell proof bag (provided by @TRDreviews)

The Cherry and Walnut units will replace the long mouthpiece with an XL8R cooling mouthpiece

An additional 10% will be given with the use of the code RBTNATION at checkout.

Please share to code with any folks you feel would be a good fit for RBT and let folks know to sign up to the news letters for the latest news and deals!

Peace,
Ryan"
 

KingSol

Active Member
I think I'm experiencing a little De Ja Vu here. Well sort of, happened to my dad with his first Milaana. I think I got a cold Splinter. I can't even get a hint of vapor until I hit 40 watts and even then the vapor is wispy at best. At 50 watts I can get vapor but I have to hold the button to a count of 8, then pull and ride the button through 3 time out cycles to see decent vapor. Another thing I noticed, in a completely dark room at 35 watts, my coil barely even glows. I have to really stare at it to see a mild glow. And at 50 watts, I can see a glow slightly but the middle doesn't glow at all. Just glows on the sides with a split down the middle as if there is 2 seperate heaters on either side. Is that supposed to happen? Or is the entire coil supposed to glow red? I have a ton of experience. My house looks like a vape/smoke shop. Between my dad, mom and myself we literally buy every ecig and flower vaporizer out. We even have 3 OG Milaanas. Tried the splinter on at least 10 different mods from 1, 2 & 3 [18650] mods, 20700 & 21700 mods, even big fat ass 26650 mods and I get the same results. Even the mods that automatically set the wattage according to the resistance it reads, even these mods start the Splinter at 45 watts. Do I need to return?
 
Last edited:

HerbieVonVapster

Well-Known Member
I can see a glow slightly but the middle doesn't glow at all. Just glows on the sides with a split down the middle as if there is 2 seperate heaters on either side. Is that supposed to happen? Or is the entire coil supposed to glow red?

Mine glows the same way. Think it's the normal way it suppose to be. The wattage seems off thou. If I did a stem at 50watts it be combustion if I held button down for 8 seconds then inhaled. If it was just one mod I would suggest that but sounds like you have ruled that one out.

Here is picture of heated coil in mine at 44 watts

ei1myf.jpg



If any of your mods are DNA welcome download the FCSHARE file maybe try the profiles in it. There's some different coil materials in it. Try hot profile or splinter watt profile.

https://forum.evolvapor.com/files/file/567-fcshare/
 

Haze Mister

Verdant Bloomer
Manufacturer
Hello!

The Splinter's mouthpiece fitting is NOT a standard 18.8mm male size. Using standard adapters puts undue pressure on the glass heater cover and can cause breakage. Only use Splinter-specific adapters and mouthpieces.

I'm sorry if this has been discussed but what's the deal here?
 

KingSol

Active Member
Mine glows the same way. Think it's the normal way it suppose to be. The wattage seems off thou. If I did a stem at 50watts it be combustion if I held button down for 8 seconds then inhaled. If it was just one mod I would suggest that but sounds like you have ruled that one out.

Here is picture of heated coil in mine at 44 watts

ei1myf.jpg



If any of your mods are DNA welcome download the FCSHARE file maybe try the profiles in it. There's some different coil materials in it. Try hot profile or splinter watt profile.

https://forum.evolvapor.com/files/file/567-fcshare/
Yeah even at 50 watts it is underwhelming. Feels like I need just 10 more watts to get where I want but I was scared to use it at that wattage. Besides, I don't think I should be using 60 watts to get what others are claiming at 27-30 watts. In regards to the DNA mods and temp control..... I don't even want to touch that yet. Before venturing off into temp mode [which I'm familiar with] I want it to work as it was designed for first in wattage mode. Don't want to find a good temp only to find out I've been overworking the splinter because it was never right in wattage mode. I also failed to mention that I did try temp mode and it was super underwhelming at 400F
I never vape above that unless through water. I'm figuring that if I couldn't get vapor at 400F then something must be running cool. Failed to mention, I tried 3 different strains. Strawberry Turbo D, Grease Monkey and Royal Kush with all the same results. It also drains the f#*k out of my batteries. After 4 bowls, I have about 60% battery left.
 

cybrguy

Putin is a War Criminal
Somehow I don't think I want to play this lets make the Splinter glow game. These aren't coils you can replace, isn't this a bad idea? Is my newbiness showing or my common sense? This is, of course, only day 2.
 
Yeah even at 50 watts it is underwhelming. Feels like I need just 10 more watts to get where I want but I was scared to use it at that wattage. Besides, I don't think I should be using 60 watts to get what others are claiming at 27-30 watts. In regards to the DNA mods and temp control..... I don't even want to touch that yet. Before venturing off into temp mode [which I'm familiar with] I want it to work as it was designed for first in wattage mode. Don't want to find a good temp only to find out I've been overworking the splinter because it was never right in wattage mode. I also failed to mention that I did try temp mode and it was super underwhelming at 400F
I never vape above that unless through water. I'm figuring that if I couldn't get vapor at 400F then something must be running cool. Failed to mention, I tried 3 different strains. Strawberry Turbo D, Grease Monkey and Royal Kush with all the same results. It also drains the f#*k out of my batteries. After 4 bowls, I have about 60% battery left.

Might be a daft question but - Do you preheat/feel heat pressure build up and inhale or press and rip (on any wattage)..

What is the resistance on your mod reading for the heater element?
 
Last edited:

HerbieVonVapster

Well-Known Member
Somehow I don't think I want to play this lets make the Splinter glow game. These aren't coils you can replace, isn't this a bad idea? Is my newbiness showing or my common sense? This is, of course, only day 2.

Totally agree but well under the 70 watt burn in at 44 watts. But would not recommend others to follow my example. Thank you for pointing that out.

It was posted to assist kingSol with his issue. So please let's not start a glowy coilly game based on my pic.

@Brainstrained

Fresh stem would let it warm for couple seconds. Then do a couple small cigar type puff till feel the heat.
After first couple hits it's press inhale.

The resistance at 70 degree is 0.226 settles at around .270 at roughly 400 degree on my splinter.
 
Last edited:
HerbieVonVapster,
  • Like
Reactions: KingSol

KingSol

Active Member
Might be a daft question but - Do you preheat/feel heat pressure build up and inhale or press and rip (on any wattage)..

What is the resistance on your mod reading for the heater element?
At 40 watts my heat up time is 8 count warm up, then I pull on it and refire through 3 timeout cycles. Really, I run out of breath by the time I get vapor. At 50 watts my warm up is 6 seconds and I pull through 2 timeout cycles and get decent vapor. Also it will get hot to my lips at that point but not at 40 watts. My resistance is reading at .23-.28 depending on the Mod [not enough difference to matter]. I definitely don't want to play the glowy game either, that's why I refused to go to 60 watts even though I felt I would get what I wanted there.

Mine glows the same way. Think it's the normal way it suppose to be. The wattage seems off thou. If I did a stem at 50watts it be combustion if I held button down for 8 seconds then inhaled. If it was just one mod I would suggest that but sounds like you have ruled that one out.

Here is picture of heated coil in mine at 44 watts

ei1myf.jpg



If any of your mods are DNA welcome download the FCSHARE file maybe try the profiles in it. There's some different coil materials in it. Try hot profile or splinter watt profile.

https://forum.evolvapor.com/files/file/567-fcshare/
Just out of curiosity, how long did you have to fire it at 44 watts in order to see that glow?
 
Last edited by a moderator:
KingSol,
  • Like
Reactions: BigJr48

KeroZen

Chronic vapaholic
You mention a deja-vu with your dad's first Milaana. So there was a second Milaana which wasn't cold afterwards right?

Did you manage to get either of these units working with you in the end?
 

HerbieVonVapster

Well-Known Member
Sorry about that had big long answer written out and lost power. That was at around 4 seconds at 44watts.

Might also might want to ask this over in mod thread since this info works across muti 510 devices. Not all members monitor different devices threads. So might get quicker mod answer there.

Sounds like you have tried it on a couple mods if all are taking a higher wattage. Then it's something with the splinter.

Check see if screw is tight on it is a thought. Maybe try different stem. Are some other thing I can think of. IDK


http://fuckcombustion.com/threads/t...ons-and-customizing.23742/page-5#post-1284114
 
Last edited:

cybrguy

Putin is a War Criminal
In wattage mode I am finding I get more charring than I would expect at just 25 watts. Might this indicate my coil resistance is too high? So far I have left my rx 2/3 at the default coil setting of .235.

I find that if I am not in a hurry I can fully extract a load at only 25 watts and that surprises me a little...
 
cybrguy,
  • Like
Reactions: BigJr48

AJS

Calm Consistency
In wattage mode I am finding I get more charring than I would expect at just 25 watts. Might this indicate my coil resistance is too high? So far I have left my rx 2/3 at the default coil setting of .235.

I find that if I am not in a hurry I can fully extract a load at only 25 watts and that surprises me a little...
25W is low for that kind of behavior.
 

KingSol

Active Member
@KeroZen
We have 3 Milaana's in total. Actually 4. My dad purchased one for my grand uncle who recently passed away so we got his back but it has a broken glass input. The only cold one was the very first Milaana and my pops was heartbroken because he waited so long and it didn't work [ran cool like this splinter] when he got it. It was returned and repaired [not replaced] and came back as a beast which led to the other 3 Milaana purchases, one being for Uncle Pootsie. 3 still in heavy use and 1 I need to send in to fix the glass.

@HerbieVonVapster
At 44 watts i would probably have to mash the button at least 15-20 seconds to get a glow like that. I put it up to 75 watts like the burn in and still didn't see a glow until about 8-10 seconds and it was smaller than yours at 44 watts.
 
At 40 watts my heat up time is 8 count warm up, then I pull on it and refire through 3 timeout cycles. Really, I run out of breath by the time I get vapor. At 50 watts my warm up is 6 seconds and I pull through 2 timeout cycles and get decent vapor. Also it will get hot to my lips at that point but not at 40 watts. My resistance is reading at .23-.28 depending on the Mod [not enough difference to matter]. I definitely don't want to play the glowy game either, that's why I refused to go to 60 watts even though I felt I would get what I wanted there.

I feel your pain.. I asked because I received my Splinter earlier on today and was underwhelmed for the first couple of bowls, I was having the same issues you describe, lack of vapour etc. So I came on here for inspiration and saw your post but from the 3rd bowl it's kickin and all's good! All that I changed myself was how I inhaled and timing of inhalation.. Hope you get yours sorted..
 
Brainstrained,
  • Like
Reactions: BigJr48

HerbieVonVapster

Well-Known Member
I would be contacting RBT if was just one mod then would point that. But you tried on a few and same outcome. Mod people are using lot less wattage. Something sounds wrong.

Got a lot smart people here so maybe I might be overlooking something but 50-60 watts is high.

Edit consider both you guys received them today makes me now wonder?
 
HerbieVonVapster,

KingSol

Active Member
I feel your pain.. I asked because I received my Splinter earlier on today and was underwhelmed for the first couple of bowls, I was having the same issues you describe, lack of vapour etc. So I came on here for inspiration and saw your post but from the 3rd bowl it's kickin and all's good! All that I changed myself was how I inhaled and timing of inhalation.. Hope you get yours sorted..
That's what I'm hoping for. I'm not giving up yet, hoping it will just kick in on one of these bowls. I do LOVE this little freaking thing and don't want to send it in for repairs. I'm going to keep toying with it but I refuse to even touch temp mode unless I get it working right in wattage first.

@HerbieVonVapster
Today will make my third day. Been through about 16 test bowls with 3 different top shelf strains.
 

Hussan311

Well-Known Member
USPS really helped me out after sending my package to a different state i got it about a hour ago and so far seems to be working really nice. I have it on a joytech espion i am running it at 30 watts and i think the res is .24 but so far i am getting good hits at 30 watts. I am just happy i got it today i didnt think i would have it untill monday at the earliest
 
Hussan311,
Status
Not open for further replies.
Top Bottom