Dynavap VapCap

Ricardo · Jul 5, 2018

@Skunkport
So basically the three things are the same with hash being the dodgiest in terms of purity?
I guess what I had yesterday (and will have again in about 15 minutes, was Pollen). It was a gift but I'm told it costs 5€/gram which is slightly more than I pay here for bud (not the UK) and although I can't compare it with other batches, it's waaaay sweeter than any hash I've ever had. The plan is to use it occasionally for extra oomph with a little herb in the vapcap through water.
Normally, just with weed, I'll get 3, max 4 heating cycles. Last night I had to give up after about 8!!!! And these were lungbusters

Skunkport · Jul 5, 2018

stark1 said:
EDC Tactical Pens for the Endgame.

Ugly lookin butt suckers, IMHO. There are some handsome ones in the wild.

I think it's too big to be a pen really and there's definitely electronics of some sort inside on one of the pictures.
There are some great-looking tactical pens but they're too narrow to make what I want, a vapcap at least 12-13cm long and double the width. I already burnt my finger on my M, I want more distance between the hot spot and my clumsy stoner grasp.

There's titanium containers but none I can find (so far) big enough, although my tip does actually fit fairly neatly in a titanium toothpick container I have on my keyring.

Maybe a cigar tube...hmmm...back to searching through aliexpress!

hanfhead · Jul 5, 2018

I figured it out. I thought it was a pen refill in the one picture but it clearly says "defense" on it. It's some kind of pepper spray canister. I found this site that when translated from chinese calls it a "wolf spray". So more googling I found this refill. https://www.amazon.com/Mace-80361-Pepper-Baton-Refill/dp/B005GT9SM6/

stark1 · Jul 5, 2018

Skunkport said:
I think it's too big to be a pen really and there's definitely electronics of some sort inside on one of the pictures.
There are some great-looking tactical pens but they're too narrow to make what I want, a vapcap at least 12-13cm long and double the width. I already burnt my finger on my M, I want more distance between the hot spot and my clumsy stoner grasp.

There's titanium containers but none I can find (so far) big enough, although my tip does actually fit fairly neatly in a titanium toothpick container I have on my keyring.

Maybe a cigar tube...hmmm...back to searching through aliexpress!

You have in this community some very talented craftsmen/artists, you need just ask.

End walla!

Don’t wanna be sucking in some wolf spray—nivver know what it’s been into.

Skunkport · Jul 5, 2018

Thanks! So it's a copy of the Asp Palm Defender from looking at those links, but their standard one is aluminium.

I have asked one of the craftsmen, but I figure he has to start from something and titanium rods as thick as I want would likely be expensive, an already made hollow cylinder might be cheaper and easier.

Anyone else you think might be interested in doing this other than Stardustsailor?

Nothing wrong with inhaling some pepper spray, I'll just eat some chili to go with it

JamesTiberiousKirk · Jul 5, 2018

Hopefully, I have got this youtube posting correct.

This the Jorge Cervantes vid on butt hash, or "culero".

Vaporware · Jul 5, 2018

grampa_herb said:
An old hippy fucked with my head once and told me how hash was made. Take a hairy individual who has not had a bath in a week and have him run naked through fields of plants for a few hours, then scrape the residue from his body.

Hackerman said:
I heard it was naked virgins running through the fields. Then, they were brought back to the castle where the king's hash preparers scraped the nubile virgins and prepared the hash for the king.

I like my version better. LMAO

Who said the unwashed hairy naked guys weren’t virgins? Probably not so nubile though... :cool:

Ricardo · Jul 5, 2018

Great video :clap:

I could live with that..... Plenty of cling film there. First thing I'd do though is flatten it out and reshape it :lol:

Also, I like this Jorge Cervantes dude - he is the collective us ('cept he ain't vaping) :spliff:

nickdanger · Jul 5, 2018

Ricardo said:
Great video
I could live with that..... Plenty of cling film there. First thing I'd do though is flatten it out and reshape it
Also, I like this Jorge Cervantes dude - he is the collective us ('cept he ain't vaping)

My first thought was how in hell could anyone swallow anything that large, much less a kilo worth... I couldn't even swallow one of those.

caliganja420 · Jul 5, 2018

Just received my Omni XL, having problems adjusting the airflow? When i loaded my first bowl it was a really hard draw, when i twist the MP i dont see the condenser tube moving? Also where the carb hole is, there is a silicone ring visible?
I have to draw very hard to get a hit

JamesTiberiousKirk · Jul 5, 2018

nickdanger said:
My first thought was how in hell could anyone swallow anything that large, much less a kilo worth... I couldn't even swallow one of those.

I imagine they train for it, like any athlete. Maybe hotdog eating contests?

StringTheorista · Jul 5, 2018

Rollingstoned said:
Just received my Omni XL, having problems adjusting the airflow? When i loaded my first bowl it was a really hard draw, when i twist the MP i dont see the condenser tube moving? Also where the carb hole is, there is a silicone ring visible?
I have to draw very hard to get a hit

I found that removing the condenser and seeing how it worked made the whole thing make more sense. Turning the mouthpiece counter clockwise (unscrewing the connection and thereby lengthening the condenser) pushes the condenser towards/into the tip and reduces airflow. I use it screwed all the way out, just enough so the threads are slightly engaged, and there is still some airflow.
If you’ve got little or no airflow, try screwing the mouthpiece all the way clockwise. If still no flow, the problem is elsewhere.

Gray Area · Jul 5, 2018

The vapcap does indeed do hash really well. I'm more than impressed... in fact it's pretty much taken over and changed my whole approach to vaping.
Nobody is more surprised than me :tup:

While we're on about pollen (which comes from a male plant) and keif, both are misused terms really.
There is no such thing as commercially available pollen. What people at really talking about is polm... and mispronouncing it.
Keif or kif was traditionally a smoking mixture used in morocco made from finely chopped flower heads (not to collect the resin glands).

Always thought the common/modern use for both these terms odd.

:peace:

JamesTiberiousKirk · Jul 5, 2018

Rollingstoned said:
Just received my Omni XL, having problems adjusting the airflow? ... Also where the carb hole is, there is a silicone ring visible?
I have to draw very hard to get a hit

If the silicone ring is visible where the carbhole is, the o-ring may be not in the correct position?

I personally dislike the omni condenser system. But that's just me.

caliganja420 · Jul 5, 2018

I dissasembled it, then put it back together, but when i spin the MP and if i take the Tip off, i dont see the condenser moving

StringTheorista · Jul 5, 2018

Rollingstoned said:
I dissasembled it, then put it back together, but when i spin the MP and if i take the Tip off, i dont see the condenser moving

Is the mouthpiece backing itself out?
Push it back in if so

caliganja420 · Jul 5, 2018

i figured it out now, the MP can only spin 2-3 times before it comes off the threads and the more you spin the more restricted the airflow, guess i will have to keep it spun midway, or just keep it tight and use the carb hole?

mrb · Jul 5, 2018

Gray Area said:
Keif or kif was traditionally a smoking mixture used in morocco made from finely chopped flower heads (not to collect the resin glands).

This was my understanding. But I only think that because that's what I've been told in Morocco. . . :shrug:

Rollingstoned said:
I dissasembled it, then put it back together, but when i spin the MP and if i take the Tip off, i dont see the condenser moving

EDIT: Ah, I see you've solved the issue. . .

I have never owned the omni stems/bodies, just the condenser/MouthPiece part, but I think the adjustment in the regular sized omni body moves the o-ring directly over/under the carb hole, reducing airflow there, as well as where the condenser enters at the mouth of the tip.

While twisting the MP in either direction. . . . .
- Can you not see the ring moving up and down through the carb hole?
- Can you not see the condenser move in and out of the end of the body when the tip is off?
- Do the two parts of the omni condenser/MP un-screw and screw together when out of the body?

The last thing is that sometimes if fitment is a bit tight, the can MP rise up out of the body instead of pushing the condenser down through the body, but this wouldn't lead to reduced airflow. . .

StringTheorista · Jul 5, 2018

JamesTiberiousKirk said:
I personally dislike the omni condenser system. But that's just me.

I like it better in the CF stem. Love the looks of the Omni stem, and the ergonomics. But it’s a bit too open even fully choked.

Ricardo · Jul 5, 2018

Gray Area said:
While we're on about pollen (which comes from a male plant) and keif, both are misused terms really.
There is no such thing as commercially available pollen. What people at really talking about is polm... and mispronouncing it.

Oh, now this is interesting. Polm! I knew bees collect pollen and take it to the female flower to fertilise it. Every schoolkids knows this.... I also know that male cannabis plants are separated from females (not sure why... I guess we want the flowers to grow more? (I know nothing about cultivation), so pollen didn't make sense to me, I thought it was Spanish slang but the word is the same... . So pollen is just Polm mispronounced. ..... Now I need to Wiki Polm....
As for kief, we just use the word incorrectly but it has become accepted jargon, clearly.
Much appreciated :tup:

EDIT : With polm or kief or pollen or hash, I really need to go full 4 Misissippi and the clouds keep coming

I think it also helps to stir it up a little halfway through, break down any lumpy bits. I love weed :leaf:

Dynalowrider · Jul 5, 2018

@Rollingstoned if you look in the mouthpiece you can see the end of the condenser which will let you know how deep you are in the tip. If closed is what you are trying to achieve, and you feel it's not closed enough, keep using it. It will not take long and it will rosin up. Doc

caliganja420 · Jul 5, 2018

Dynalowrider said:
@Rollingstoned if you look in the mouthpiece you can see the end of the condenser which will let you know how deep you are in the tip. If closed is what you are trying to achieve, and you feel it's not closed enough, keep using it. It will not take long and it will rosin up. Doc

Seems like it hits the best when you use the carb hole with the mouthpiece fully closed, if i turn it and leave it there it eventually moves again, it does get very good tasting hits, its incredible

kushkush · Jul 5, 2018

Ricardo said:
As for kief, we just use the word incorrectly but it has become accepted jargon, clearly.

The only thing I’ve ever read about Kief is that it’s synonymous with Tricomes... that hold most if not all the THC.

:2c:

Summer · Jul 5, 2018

@TheSaddestShitIsImBadAsIt, take a look at the Best of Vapcap thread. Many helpful heating tips with pics.

http://fuckcombustion.com/threads/best-of-dynavap-vapcap.24345/

Rollingstoned said:
I dissasembled it, then put it back together, but when i spin the MP and if i take the Tip off, i dont see the condenser moving

Do this:
- screw the tip clockwise. This is the fully open position.
- take the tip off. You'll see the condenser is fully recessed into the stem.
- unscrew, counter-clockwise, the mp as far as you can before it comes off the threader.
- now push the mp & condenser assembly completely into the stem so that the mp is butted up against the stem.
Now you will see that the condenser protrudes/extends from the tip end of the stem. When this protraction is inserted into the tip it blocks air flow. Depending on how much you unscrew the mouthpiece between fully closed & open will determine how much air flow is blocked.
- now if you screw the mp clockwise again while holding it flush again the stem, you will see it retract into the stem.

There was a short DV video showing this, but I don't have the time to find it. Also, someone posted pics of the stem retracted & protracted.

Here's a link to Squiby's Best of VapCap post:
http://fuckcombustion.com/threads/best-of-dynavap-vapcap.24345/page-2#post-1189989

I like it fully closed/clockwise, as I like the most air flow I can get. Problem for me is that even with the most air flow I find the carb hole too small to get as much as I like. So what I did was remove the condenser & insert just the mp into the stem.

caliganja420 · Jul 5, 2018

Summer said:
@TheSaddestShitIsImBadAsIt, take a look at the Best of Vapcap thread. Many helpful heating tips with pics.

http://fuckcombustion.com/threads/best-of-dynavap-vapcap.24345/

Do this:
- screw the tip clockwise. This is the fully open position.
- take the tip off. You'll see the condenser is fully recessed into the stem.
- unscrew, counter-clockwise, the mp as far as you can before it comes off the threader.
- now push the mp & condenser assembly completely into the stem so that the mp is butted up against the stem.
Now you will see that the condenser protrudes/extends from the tip end of the stem. When this protraction is inserted into the tip it blocks air flow. Depending on how much you unscrew the mouthpiece between fully closed & open will determine how much air flow is blocked.
- now if you screw the mp clockwise again while holding it flush again the stem, you will see it retract into the stem.

There was a short DV video showing this, but I don't have the time to find it. Also, someone posted pics of the stem retracted & protracted.

Here's a link to Squibly's Best of VapCappost:
http://fuckcombustion.com/threads/best-of-dynavap-vapcap.24345/page-2#post-1189989

I like it fully closed/clockwise, as I like the most air flow I can get. Problem for me is that even with the most air flow I find the carb hole too small to get as much as I like. So what I did was remove the condenser & insert just the mp into the stem.

I am getting rather harsh hits, and abv is realy dark brown
I am using a single flame torch, heating at the bottom of the cap, and spinning it the whole time
Also, how many hits per bowl, i have noticed about 3 but if i go for more it really chars the weed
Any good tips for heating would be appreciated

Dynavap VapCap

Well-Known Member

Well-Known Member

is high

Lonesome Planet

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Collector of Functional Art

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Accessory Maker

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

happy camper....

Long Island, NY

Well-Known Member