Recent content by Vambo1980

Heating elements fail open circuit and short if turned on and off frequently. The issue is due the expansion and contraction over time causes fatigue and stress.

I'm hearing ya! Comprensisive information. Nicely written too. Thanks.

I like the flat mouth peice better also. I just like the feel and seal it gives. One thing I forgot about was the smell with conduction vapes, I have to say it's a smelly vape if not cleaned out every 2 or 3 bowls. I also find it gives me a much more sedative hit than any of my other vapes. I...

Another happy customer here. @Davinci_vaporizer stepped in and the right thing has happened! Davinci provided a prepaid FedEx return label and also sent out a new unit. I've had 3 sessions this evening and not an issue. A big thanks for doing the right thing Davinci. No further complaints...

No probs. I've been using numerous Samsung 25R cells for about 750hrs or more in my crafty. All of them are still fine and although they don't heat up the the alternate as fast as a new one they have been great for back up batteries. I have given my crafternate to a mate with a few of the old...

Hi, You cannot get a 6000mah 18650 It will be fake. You must use a genuine high quality high discharge battery. Even if you could get one I doubt very much it will work how you are expecting. http://www.torchythebatteryboy.com/p/18650-batteries-chargers.html?m=1 I found this site above...

Hi Gav, The flashing red/yellow light could indeed be a common signal for other faults. If for example the heater burnt out or some how became open circuit. I doubt very much it is that though, most likely be the thermal fuse that is mounted at the bottom of the oven base mount/housing. If the...

Hi Gav, Welcome to FC You could search my old posts for more info. The yellow/red flashing error for myself was the thermal fuse which connects in series through the heating element. I bypassed this fuse and soldered the heater element wires direct to the crafty main board. Perhaps not a good...

If you leave them in ISO for more than a few hours the adhesive breaks down and turns to jelly. If you reclaim the oil for any purpose then you should remove them altogether in my opinion.

Hi, I always burn new pads off before use with a torch. They always have a horrible machine oil taste with out it. I then ISO wash used pads in warm ISO and let dry and then burn off again. You can still taste a little funk on the first couple of hits of a cleaned used pad but it much better...

I thought I would try one last go with IQ before I package it up and send it back. And what do you know? it worked.. well a bit. It worked with nothing in for a good few minutes so i stopped it loaded it with some blue dream and had a lovely session for about 8 minutes on it's own. Then it...

Wow Alex, That is a great mod, it's very nicely done. Thanks for sharing. Little update about my old girl.. she is still tickling my tonsils. She still gets a run nearly every day. Altough not getting any fitter. I'm up to 896 hours on my 2.05 firmware model. The usb connector has now failed...

Hi Tru3leg3end Thanks for the info, although I don't want to mess with the unit. It literally didn't work a full session out the box. If I'd have used it for a week or two and been enjoying it I would be fiddling with it, but for £200+ I'd expect quality control to be better. I've got lots of...

I thought I was covered by 14 day right to return UK trading rules. But I'm not sure.. The experience I've had just makes me want my money back. It's like the once bitten twice shy feeling and I've lost faith in this company hence me not really interested in emailing them explaining it all when...

Hi everyone. I went ahead with my VAS and brought one of these. On a fathers day discount. I received tbe unit today but It's not been a good start. The unit just cuts out after it's been turned on for a minute or two. It's also strange on charge see my videos here...