Recent content by Costanza

So my PD went cold on me a few weeks ago. And since then I've been struggling to match its efficiency with my SSV. :/ I'm sure its the plug, as the pd worked fine up until then and I'm very careful with it. I would just like to know if this adapter would work...

I've had my Launch Box for a couple of weeks now and it does seem to work. However, in order to close the current I've got to twist the battery around to try to find the right spot. The Energizer batteries are a looser fit so I've also got to angle the battery up or down, but even with the stock...

I'm just about sold on this vape for my on-demand portable vapor needs. My only hold up is battery life. My idea is that one battery = (roughly) one trench? And if you pull out the battery a bit while not inhaling (conserving batt. life) perhaps two? This means that the two stock batteries will...

Hello, I'd usually pop in the chat to ask small questions like this, but this is the problem: Could somebody in the know let me know why I can't log into the chat room anymore? It'd be a great help.

NoSmoke, thanks for your answer. Until then, which part should I be trying to turn? The threaded piece coming out of the nut or the nut itself?

Hah no, no, no. I wouldn't blaspheme against my beauty. I wanted to be sober for the first time I tried my SSV is all. Start at baseline to get a good bearing on the SSV's capabilities and all that. So I restrained from hitting the ;pd;. Until now, that is :D.

So I'm worried that my SSV may have been damaged during shipping. There aren't any instructions on how to attach/detach the knob in the manual. And I figured that I would still be able to adjust the temp without the glass knob but nothing's turning. I can only see a nut and part of a screw...

I've got a question for anyone who's tried the SSV and the VHW (trying to avoid another vs thread). How do they compare? Especially concerning the vapor:air ratio. So far I've seen it said that the hits are comparable but the VHW has the advantage in taste and producing an even cook. Also...

I thought that when the red light went on that meant that the element was heating up? When I turn the variable resistor counter-clockwise it lights up. It seems as though when I turn it clockwise it cools down, is this right?

I had the same smoke come out around the end of the sleeve, made more visible when I lightly blew on it or flapped the end of it (with a fingernail or tool). I figured it was some natural pre-use dissipation. I have a dark spot on my heating element but took that to be normal as well. I cut...

Hey, no problem. I appreciate the quick reply. I just wanted to check about the silicon sleeve before I cut it. Is this too long? And the VCB:

I usually wait the ten minutes before trying to use it, hoping that it helps. But I have the same problem no matter how long I've been trying to hit it. No, the glass tip doesn't make a seal no matter what angle I hold it at. I've even taken out the VCB and inhaled directly from the lower bowl...

So I got my VHW/ProWT/Jetflo yesterday and I'm having some problems. It just isn't vaporizing well at all. I checked and I've got an airtight seal throughout the water tool and if I hold the VHW at just the right angle I don't get too much air coming in where it connects to the VCB. Maybe its...

Knuckles was the shit. Gliding and wall climbing beat super-speed any day. Anybody else have the Sonic & Knuckles cartridge that had the slot on top for games w/ easter eggs? No tattoos, however. This is turning into the Knuckles Appreciation thread. :argh:

Considering that it's still in the brainstorming stage, I'm assuming that this new water tool's going to come out a while after the VHW does? I was planning on buying the VWT Pro with the VHW but now I'd want this one. :/ As for the design, I agree that it'd be much more comfortable to be able...