New glassware - Dumb question: How high should water go?

Status
Not open for further replies.

buglaserbug

New Member
I just bought this new piece and, while I feel stupid for asking, I'm not sure how high to fill the water.

Any help? Should it go up past the second inlet hole (into the main chamber) or should I leave it lower than that? I feel as though if I leave it lower, then the vapor isn't forced through the water? I don't know. Sorry for the dumb question! =D
z9N0RTA.jpg
 
buglaserbug,

SpruceGruve

Bag of sand in hand,Eyeing up the gold statue
There is no right level,suck as hard as you normally would emptying the chamber.
If water hits your lips/mouth empty it a bit more
 
SpruceGruve,

Rusty778

Getting Lost
I find it easiest to get a video camera and take some video of you hitting it to see how much of the perc fire's with given water levels. Keep in mind that when you draw, some of the water in the stemless will be forced by your lung pressure into the main tube, raising the water level. So for some pieces, just covering, or even just beneath the perch may be ideal. Your milage will vary, so experiment! :science:
 

buglaserbug

New Member
Wait, so it doesn't really matter *where*?

My 'concern' is that filling it to the red would cause the water to leak out.
Filling it to the blue means that the water won't pass through the perc.
Green seems right, but... super precise?

Also, I should point out that I'm new to the bubbler scene, so maybe I have some basic misunderstanding of wtf I should even be doing. =)

d7Patnf.jpg
 
buglaserbug,

SD_haze

Well-Known Member
Perfect, thanks for the help! I guess in the end it won't matter all that much. =)
I'll chime in with my :2c:

I think it does matter in a lot of cases, especially with vaporizers.
If you're trying to use a vaporizer with a lower temperature setting or a small load size, then too much water can over-diffuse the vapor. I would try to go as low as you can with the perc firing normally. Use a mirror or camera to see the action better.

If you're getting irritation & lots of coughing at that minimal water level, only then would I slightly increase the water level. Never, ever as high as the frosted ground glass joint.
 

buglaserbug

New Member
I don't think that top inlet hole is an inlet hole. It is solid and there for support. The blue line you drew in the pic should be the sweet spot.
Alright, reporting back that you're totally right. It wasn't an inlet at all. You'd think I'd checked *after* I used it.
I'll chime in with my :2c:

I think it does matter in a lot of cases, especially with vaporizers.
If you're trying to use a vaporizer with a lower temperature setting or a small load size, then too much water can over-diffuse the vapor. I would try to go as low as you can with the perc firing normally. Use a mirror or camera to see the action better.

If you're getting irritation & lots of coughing at that minimal water level, only then would I slightly increase the water level. Never, ever as high as the frosted ground glass joint.
Awesome, thanks for the advice! I'll do some camera shooting to figure it out (I am using smaller loads on low temps).
 
buglaserbug,

clouded vision

Well-Known Member
It will probably fire best with the water somewhere right around the disc level. I actually has a honeycomb that fired best with the water just below the disc. With the stemless design, the water in the stem gets displaced into the can slightly raising it. Also with a honeycomb, overfilling can have a negative effect on the diffusion. My GBD honeycomb is horrible when over filled but can really stack when it's at the perfect level.
 
clouded vision,

Caligula

Maximus
Your honeycomb piece is similar to one of mine. These vids may help.

They were shot in HD so kick up the resolution and increase the window size to get a clear view.

 
Caligula,

KidFated.

Unknown Member
@Caligula since their "new" to the bubbler scene, tell Bug about why your water is a reddish color? Bug may wonder why their bubbles dont stack as tall or about the color itself. I would inform them but im not too knowledgable about those extracts myself.
 
KidFated.,
  • Like
Reactions: Caligula

buglaserbug

New Member
Dude, you folks are great.

@Caligula Thanks for the demo, and the link to the extract thread. That E-Nano looks amazing. I love my Vapor Bros so far, but will eventually want to get a new piece.

@KidFated. Thanks for asking for me----I had no clue this even existed.

Everyone else: Thanks for the advice. Got it working well last night, will try again today.
 
buglaserbug,
  • Like
Reactions: Caligula
Status
Not open for further replies.
Top Bottom