The Plug-In Supreme Vaporizer

LAWTHEONE

CLOUDYWITHFOG/ZEROVISIBILITY
You have to verify it with Ed but I’m pretty sure he said this one can’t be torched.
 
LAWTHEONE,
  • Like
Reactions: Morty

Abysmal Vapor

Supersniffer 2000 - robot fart detection device
:D So V6 is still aluminum.. Hopefully someday Supreme will make it to Titanium or Stainless.. :))
And yes it looks like a the bastard child of Jcats mod.. :D

Yes the Supreme 4. Something about the welds being compromised without regulated heat. I think he said the aluminum is good under 1300° but he doesn’t recommend going over 800°. I run mine anywhere between 475° to 600° depending on the situation and how much effects I want.
Hmm Are you talking Fahrenheit or Celsius ? Hmm now that Supreme is no longer torch-driven might it be that the maker have changed the Gopel from claiming it is Safe to blast it with 1200 C torch (2300+ F ?!?) to not go over 800 F? Or is that unsafe just for the welds,not for the user ?
 
Last edited:

LAWTHEONE

CLOUDYWITHFOG/ZEROVISIBILITY
Yes the Supreme 4. Something about the welds being compromised without regulated heat. I think he said the aluminum is good under 1300° but he doesn’t recommend going over 800°. I run mine anywhere between 475° to 600° depending on the situation and how much effects I want.

I did my first dab in this this weekend and it was phenomenal!
 
Last edited:
LAWTHEONE,
  • Like
Reactions: Morty
My V6 had landed. I've had it for an hour and I'm already melted. Also found out that the pipes and WPAs for the Lotus butane vape are compatible with this. I'll be posting vids to reddit as soon as I get the chance.
 

LAWTHEONE

CLOUDYWITHFOG/ZEROVISIBILITY
0vq9xi1huy2h1o91.jpeg
hdvxo25gs6qsvo9k.jpeg
 
LAWTHEONE,
  • Like
Reactions: lazylathe

LAWTHEONE

CLOUDYWITHFOG/ZEROVISIBILITY
I just found a sick way to super microdose. You can turn your heat way down too. The lotus water piece adapter!!!
I got it from Sneaky Pete
 

lazylathe

Almost there...
I have been using a new technique the last few days and I am getting way more medicated off the same amount of material! It's crazy. Actually feel more stoned than usual.

Usually I drop a load onto the screen and take it all in one hit, hold for a bit and exhale.
It's worked for years and always got the job done.

My new technique is to take the same load and hit it 3 to 4 times, taking smaller hits and then a big lungful of air. I just whitewall and then remove and pull in enough air to fully expand my lungs and chest.
Maximum surface exposure for absorption.

There is an article I read that I will link to when I locate it!
 

PPN

Volute of Vapor
I have been using a new technique the last few days and I am getting way more medicated off the same amount of material! It's crazy. Actually feel more stoned than usual.

Usually I drop a load onto the screen and take it all in one hit, hold for a bit and exhale.
It's worked for years and always got the job done.

My new technique is to take the same load and hit it 3 to 4 times, taking smaller hits and then a big lungful of air. I just whitewall and then remove and pull in enough air to fully expand my lungs and chest.
Maximum surface exposure for absorption.

There is an article I read that I will link to when I locate it!
This is looks similar to my technique, I was never a one hit guy and the inhalation of fresh air at the end of the hit makes things smooth!
 

Pyah

Well-Known Member
My V6 had landed. I've had it for an hour and I'm already melted. Also found out that the pipes and WPAs for the Lotus butane vape are compatible with this. I'll be posting vids to reddit as soon as I get the chance.

Whats your favorite temp to use with the lotus wpa? It says dont go past 550, but I have been wanting to push it to 600 for a 1 hit dosage in convection mode.
 
Whats your favorite temp to use with the lotus wpa? It says dont go past 550, but I have been wanting to push it to 600 for a 1 hit dosage in convection mode.


I hang around 520f or so. I haven't tried anything higher

Side note, I took the thermometer of from my v3 and fixed it onto the handle I built. Getting waaaaay better readouts. I heat the block to 530f now (about 750 on my PID controller) with no signs of ware on the holder plates. Love this thing to death
 
Last edited by a moderator:
CABtheFISHKING,
  • Like
Reactions: Morty

Pyah

Well-Known Member
I hang around 520f or so. I haven't tried anything higher

Side note, I took the thermometer of from my v3 and fixed it onto the handle I built. Getting waaaaay better readouts. I heat the block to 530f now (about 750 on my PID controller) with no signs of ware on the holder plates. Love this thing to death

I guess I didnt think he was referring to the temp of the block and not the PID temp. 750 seems to be pushing it pretty high though. I think I need to rig a thermometer up to the block to compare the temps.
 
Pyah,
  • Like
Reactions: Morty
I guess I didnt think he was referring to the temp of the block and not the PID temp. 750 seems to be pushing it pretty high though. I think I need to rig a thermometer up to the block to compare the temps.

So far no real ware. I am considering 3D printing a custom silicone mold for more high temp durable connection piece.
 
CABtheFISHKING,
  • Like
Reactions: LAWTHEONE
So I was going to make a custom gasket for the Sv6 out of food grade RVT600 with a 3D printed mold... but my laptop decided to NOPE on me and throw a tantrum before I could 3D print the mold. It's in the shop as of now and hopefully I'll have it made soon. I'll keep you al posted
 

Pyah

Well-Known Member
I finally made a handle out of some dowel rods, hot glue, and some paracord. It feels a lot sturdier now. Ive been running it on 525 on the PID for the stock bowl, and 635 for the lotus WPA.
 

lazylathe

Almost there...
My controller went balls up and my Daily Driver is out of commission...
The backups are getting a serious workout in the meantime!

It's great to see some new people around here using the S4!
Once you tame it, it will be the vape you always reach for.
 

Mister G

Deceptively Old Fart
S4 still my daily driver.

Got a med card recently and using more oil pens and concentrates, but forcing air through the world's most advanced and powerful convection heating element to mummify flower can't be beat.

I rip and stuff, no grinding needed and still better extraction than you'll find from other "heavy hitters".
 
My laptop hard drive is shot and my laptop needs a complete rework. In the meantime I've added a little steel plate in between the Sv6 block and the flat coil creating a buffer allowing for better heating at higher temps without leaving a tiny melted coil imprint. Currently cruising at 460 f on the block with the box set to 735. I love the Supreme V6 so much, I wish it was more popular
 
Top Bottom