stardustsailor

Well-Known Member
Accessory Maker
Dendrobates auratus

Green%20and%20Black%20Poison%20Dart%20Frog%20-%2005.jpg


Aka Green 'n' Black Poison Dart Frog .
:freak:


Mica-Epoxy composite over Titanium .

https://sdsvcstems.blogspot.com/2018/07/the-making-of-mica-resin-titanium-stem.html

Cheers
 

DDave

Vape Wizard
Accessory Maker
@DDave, FWIW I think the OD of the 14mm wand could be widened a bit. Doesn’t fit quite as snugly into the joint as my 14mm ELEV8R WP adapter. Awesome piece overall just future feedback
Thanks.

If it's not air tight, then it's a defect. With the size of the joint, was going dual purpose. It had to seal in a 14mm female joint and also had to fit inside a dynastash.

Does that elev8 piece fit in a dynastash?

I am in process of another model with XL length, but will have same joint.
 

Megaton

Well-Known Member
I've just received my first double jet lighter and water piece!

Any tips re using the double jet? I tried it with an SS tip but it clicked so quickly without producing much vapor at all.

Only have a fat mouthpiece at the moment, but i have ordered a @DDave water wand. The mouthpiece does seal, but i'm sure the glass on glass would be better!
 

Hippie

Well-Known Member
Most common mistake with flames is the distance.
You want to be heating in the halo of the flames, well away from the concentrated power of the peaks imo.

Too close and the cap will click early and/or the load will be scorched.
Too far away and it'll take longer
Sooooo I'd errr on the side of caution with your first few bowls by starting too far away and move it closer as you feel your way with it all m8. It may take a few goes but at least you won't waste any this way :)
 

Hogni

Honi soit qui mal y pense
If you are looking for a boro glass stash tube for the DynaStash perhaps this could work?
I only own a DS XL so I don't know the measures of a regular DS.
Diameter is 14 mm (should fit), length is 100mm (don't know)

And possibly this could work as a 125mm water wand?
 
Last edited:

-dab8-

Dyna-saur
If you are looking for a boro glass stash tube for the DynaStash perhaps this could work?
I only own a DS XL so I don't know the measures of a regular DS.
Diameter is 14 mm (should fit), length is 100mm (don't know)

And possibly this could work as a 125mm water wand?
Ooooo! Interesting. At that price, certainly worth a try.


Unrelated, for fun I started at the beginning of this thread for a look at how all this craziness started. Anyone try the pyrovap? Obviously not available anymore, but curious to hear about how it was.
 

nickdanger

Collector of Functional Art
If you are looking for a boro glass stash tube for the DynaStash perhaps this could work?
I only own a DS XL so I don't know the measures of a regular DS.
Diameter is 14 mm (should fit), length is 100mm (don't know)

And possibly this could work as a 125mm water wand?
These appear to be open on the end opposite the threading. 100mm might be too long also.
 

Jdlpsc

New Member
I have a question about putting the cap on. When you put the cap on does it rub against the tip enough to shave the metal? I'm worried about inhaling little metal shavings from putting the cap on.

This might sound dumb, but it's something I worry about.

Thanks!
 

stardustsailor

Well-Known Member
Accessory Maker
I have a question about putting the cap on. When you put the cap on does it rub against the tip enough to shave the metal? I'm worried about inhaling little metal shavings from putting the cap on.

This might sound dumb, but it's something I worry about.

Thanks!

I used to worry about that myself too,you know !
At first ,I thought : " Oh ,comm'on you 're inhaling at least 1000x more
amount of brake pad dust & tire gum micro-particles every fuckin' day ,
since you live in an urban area
.Let alone the rest of the urban airborne crap ".

Well, I was not actually satisfied by that ,
neither it gave any clues or definitive answer to my worries.
Later I thought : " Nope ! The sticky herb act as a filter to those nasty metal micro-shavings .
Everything's cool !
"

But still I was not 100% confident about the health safety of these shavings .

That was before ...
Nowdays ,it has already became a part of the "ritual" .
I'm always wetting the threads before placing the cap.
How ?
A drop of water or tea (no sugar ,please )
or even some freshly synthesized spit rubbed on the threads ,will do
( but at this case the sizzling sound and the smell of toasted lysozyme
& amylase may be some things that someone needs to get used to ,though ) .
Lubrication ,it is .

As also is important to get to know your cap.
Where it applies pressure at the tip.
Before inserting to / removing from the tip ,
press at those two (always opposite to each other ) "pressure points"
on the cap.
That will relief most of the spring-like tension of cap ,at those points.
Slighty press the cap-thus temporarily deforming it - ,before inserting it on the tip.
That will greatly reduce the production of metal shavings .

Lubricate the threads &
-slightly -press the cap before inserting on or removing it from the tip .

I made those two things a part of the whole VC ritual.
'cause I had the same worries like yours .

I've seen great results -regarding the degree of wear at the tip's threads - ,by doing so.


BUT IF...
you're still feeling insecure :

According to the OSHA for an 8 -hour shift ,
the limit of inhalling Ti dust ( ff it's fine enough ,it is considered as TiO2 )
is 15 mg / Cubic meter of atm. air .

Just a sec to make some calcs ...

- The whole tip weighs ~ 3 grams = 3000 mg .
- 3000 / 15 = 200 .
- 3 x 7 x 10 =210


Ok ,I'm back !

You will have to turn the whole tip into fine dust ,
then disperse all of the dust in the air of a room
of 10 meters length ,7 meters width and 3 meters height,
and assuming that the dust never settles and new dust amounts are replacing the ones inhaled,
still you are allowed to work for an eight hour shift ,
in that environment without the use of any personal protective equipment .
For every productive day of your life !

https://wcam.engr.wisc.edu/Public/Safety/MSDS/Titanium.pdf

https://www.atimetals.com/Products/Documents/sds/EuropeanUnion/EU-EN/SAC/SAC020 Titanium Fines Saw Fines, Grinder Fines, Saw Swarf, and Sponge (-20) EU-EN Rev4.pdf


Cheers.
;)
 
Last edited:

-dab8-

Dyna-saur
I used to worry about that myself too,you know !
At first ,I thought : " Oh ,comm'on you 're inhaling at least 1000x more
amount of brake pad dust & tire gum micro-particles every fuckin' day ,
since you live in an urban area
.Let alone the rest of the urban airborne crap ".

Well, I was not actually satisfied by that ,
neither it gave any clues or definitive answer to my worries.
Later I thought : " Nope ! The sticky herb act as a filter to those nasty metal micro-shavings .
Everything's cool !
"

But still I was not 100% confident about the health safety of these shavings .

That was before ...
Nowdays ,it has already became a part of the "ritual" .
I'm always wetting the threads before placing the cap.
How ?
A drop of water or tea (no sugar ,please )
or even some freshly synthesized spit rubbed on the threads ,will do
( but at this case the sizzling sound and the smell of toasted lysozyme
& amylase may be some things that someone needs to get used to ,though ) .
Lubrication ,it is .

As also is important to get to know your cap.
Where it applies pressure at the tip.
Before inserting to / removing from the tip ,
press at those two (always opposite to each other ) "pressure points"
on the cap.
That will relief most of the spring-like tension of cap ,at those points.
Slighty press the cap-thus temporarily deforming it - ,before inserting it on the tip.
That will greatly reduce the production of metal shavings .

Lubricate the threads &
-slightly -press the cap before inserting on or removing it from the tip .

I made those two things a part of the whole VC ritual.
'cause I had the same worries like yours .

I've seen great results -regarding the degree of wear at the tip's threads - ,by doing so.


BUT IF...
you're still feeling insecure :

According to the OSHA for an 8 -hour shift ,
the limit of inhalling Ti dust ( ff it's fine enough ,it is considered as TiO2 )
is 15 mg / Cubic meter of atm. air .

Just a sec to make some calcs ...

- The whole tip weighs ~ 3 grams = 3000 mg .
- 3000 / 15 = 200 .
- 3 x 7 x 10 =210


Ok ,I'm back !

You will have to turn the whole tip into fine dust ,
then disperse all of the dust in the air of a room
of 10 meters length ,7 meters width and 3 meters height,
and assuming that the dust never settles and new dust amounts are replacing the ones inhaled,
still you are allowed to work for an eight hour shift ,
in that environment without the use of any personal protective equipment .
For every productive day of your life !

https://wcam.engr.wisc.edu/Public/Safety/MSDS/Titanium.pdf

https://www.atimetals.com/Products/Documents/sds/EuropeanUnion/EU-EN/SAC/SAC020 Titanium Fines Saw Fines, Grinder Fines, Saw Swarf, and Sponge (-20) EU-EN Rev4.pdf


Cheers.
;)
A doctor who listens and cares; Dr. Stardustsailor
 

Hippie

Well-Known Member
Titanium is not only safer than aluminum, but less likely to have British persons correct you on the spelling and pronunciation.

Al - you - mini - um :doh:
Foreigners are funny :freak: (<< British teeth)

I wish people wouldn't read Ti as tie, it always takes me a second or 2 to think Ohh Titanium


I have a question about putting the cap on. When you put the cap on does it rub against the tip enough to shave the metal? I'm worried about inhaling little metal shavings from putting the cap on.

You can pinch and roll the cap to get the perfect fit.
I say can :)
Do that. I do that to every cap so the cap is loose enough to be pulled off with my stash tin magnets but also tight enough to stay on and lift the stash tin if tilted at an angle and lifted
.... like George explains half way thro this video
 
Top Bottom