Multi-brand HEALTHY RIPS FURY

[LabPong]

I know that one of the main issues with the Fury 1 was the silicone screwing up the taste. My question is, was it only coming from the stock mouthpiece? In other words, if you use the Fury 1 with a glass piece (bubbler, WPA, or bent stem), does that negate the taste issue?

Good question, I would like to know that as well.

Also, one of the differences between the Fury and Fury2 as I understand....is the glue used to seal off the wires into the heater. Not sure if that would also cause any tastes issues? It is in the air path...correct?

 

[HealthyRips.com]

Also, one of the differences between the Fury and Fury2 as I understand....is the glue used to seal off the wires into the heater. Not sure if that would also cause any tastes issues? It is in the air path...correct?

Thank you for your questions! We did change all the silicone for our FURY 2 as well documented in this thread. This silicone also seals off wires to the heater - we have never used glue for any seals - that is misinformation.

All the Best!
Healthy Rips Team
https://www.healthyrips.com

 

[lockie]

I only have the Fury 2 but if you use glass instead of the regular mouthpiece, the taste will always be better even without water, way easier to clean and refill imo. (With glass stem) When I'm done with a bowl, I just inhale the last hit with the glass piece, pull it out of the Fury and exhale so the ABV just shoots out of the glass into the container I'm aiming at and then reload by inhaling/poking at the grinder. I'm pretty sure it is the blue silicon making the seal in the mouthpiece that makes the flavor change but I haven't taken apart the entire mouthpiece so I'm not positive.
Dish soap would be okay for washing, just make sure to give it a nice warm rinse afterwards.

 

[C No Ego]

So, I got into a habit of placing a finger over the intake holes at the end of the session to add some more heat in there to finish it... well my sticky fingers clogged the little holes so a few days I'm realizing the Draw is not working ?? I finally realize the holes are clogged! so I use a small safety pin and clean out the little suckers and it's like new! just hold the unit up right while you clean and look under to clean it. this lets any debris fall down and out and not into the unit...

edit- a great way to add a bit of heat to your Fury Session instead of fingering it . my fury 2 unit sits on the bubbler upside down, cup your hand over the unit on an angle to create a small airspace and push one side of your hand down to the unit and the other about an 1/4 1/2 inch away for the air in... you can open and close your hand some during draw to change flow but seems like a way to top this Puppy out @ a high heat

another trick to pull an extra hit out @ sessions end ( Jef sessions ruined my sessions expression !!!) is to lift the unit off the WPA while wpa is in the bubbler and then clear the bubbler removing wpa

 

[OF]

Still working on a custom fix for the WPA adaptor but lately I have be getting by with standard mouthpeice. Kinda funny, but I take a drink of water and leave a bit in my mouth and then bubble the incoming vapor through the water in my mouth. Like an in mouth bubbler - Kinda weird, but it works. Peace

I've got a suggestion for you. Get some traditional pipe cleaners (cotton and wire), this being my favorite brand:
https://www.amazon.com/Dills-Regula...1525627051&sr=8-2&keywords=dill+pipe+cleaners
http://www.acehardware.com/product/index.jsp?productId=29370816

Avoid craft store ones (chemicals) and those with bristles (plastics), still with the all cotton and metal ones. Fold a couple up and put them in the upper chamber, above the screen over the load. Then drip some water (enough to make them damp, but not enough to flood down into the load) before use. Water will evaporate and cool and moisturize the vapor as it passes, just like a bubbler would. You just need to add a drop or two from time to time to make it up.

I just got my Fury 2 (always late to the party.....) and am getting to know it so I haven't tried this here yet, but it works very well with Solo/Air where the spaces are smaller (only one pipe cleaner). I'm confident it'll work here even better.

Weekend regards to all.

OF

 

[lookhigh]

Hey @OF I can say this works well. Removing the screen is an option for easier cleaning. The honeyed cotton can be vaped.

 

[OF]

1) what accessories would you recommend for a 60+ year old husband and wife used? Should I get the glass mouthpiece, the bubbler (any good?), screens? All I have is the WPA, but I don’t think that’d be the best for them since they don’t have a water pipe

No need to guess on this, we have the undisputed expert on such things, our very own @Vitolo (AKA 'the sage of the High Desert') who just addressed this very question a few days back:
http://fuckcombustion.com/threads/paying-it-forward-a-new-direction.13802/page-15#post-1248431

"Even after watching videos, and live demos, most declined the extra glass mouthpiece or water adapter.
They liked using the unit self contained."

When such folks turn the extras down, especially when they are free, that's worth considering......

OF

 

[BabyFacedFinster]

No need to guess on this, we have the undisputed expert on such things, our very own @Vitolo (AKA 'the sage of the High Desert') who just addressed this very question a few days back:
http://fuckcombustion.com/threads/paying-it-forward-a-new-direction.13802/page-15#post-1248431

"Even after watching videos, and live demos, most declined the extra glass mouthpiece or water adapter.
They liked using the unit self contained."

When such folks turn the extras down, especially when they are free, that's worth considering....

Damn, this thread is getting popular. Some heavy hitters showing up around here.

I use the regular mp with a bowl screen when I have the Fury 2 out and about. This is when it's the most stealthy and most convenient. From what I can tell, this is probably the setup that will be used when the dosing caps arrive. It also seems to be the only method when using the concentrate pad. This I tried recently, and it was awesome.

I use the wpa when I'm hanging out at home vaping flower. I have my workshop area which is my "hub" of all my vaping shit. This is where I have my plug-in vape which I use most at home. However, I do like to vape while on the couch in the living room. This is where I'll load up the wpa and bring the Fury with me. It's like my satellite vape at home and since stealthiness doesn't matter, I'll use the wpa for the longer pathway and slightly cooler hits. Maybe even attach a j hook or a bubbler. We'll see what happens when the dosing caps arrive.

 

[OF]

since the load sits there and the bowl is still hot when you turn off the device the whole load as to be consumed in one session, right ?

No, that's not right. While the flavor will no doubt be spent early on, any THC (etc) you don't consume simply condenses elsewhere in the load. Think about it, nothing is destroyed (no chemical reactions like blazing), the THC doesn't 'leak out', where else could it be by waiting for more heat?

Several guys (and a few women) reported leaving the stem of their PD in the unit OVERNIGHT to find stale taste but more or less full potency next day. I myself performed this experiment. Interrupted sessions on conduction vapes are not fatal. Not to worry.

If blue silicone is used yes it will stop airflow entirely covering up the bottom hole.

Are you sure? Mine doesn't, completely. Some still leaks in the charge port if I tape up the intake. Restriction increases, but it still draws. Tape up the charge port too and it's further restricted, but still draws. Then tape up the 3 buttons and it finally is pretty tight........

Or simply blow in the charge port.....what happens? Air 'gushes' out the intake holes? Plug them and it comes out the MP instead?

I don't think it's accurate to say 'it will stop the airflow entirely', at least for the one I have (and now have to peel the tape off of.......

On the topic of what to carry the capsules we don't even have yet I plan to use 'centrifuge tubes', small snap top vials like the one here on the left end of my VM kit (full of herb here):

Amazon carries some sizes, EBay many more. Pointed ones are handy in that you can use the end to pack the load. Hopefully they'll fit the 2cc size:
https://www.amazon.com/Neta-Scienti...=1525658087&sr=1-11&keywords=centrifuge+tubes

If not, I'll be using the fives. I already do this for the FM 'pods', it works well. I also have a 5cc one full of herb (four loads, give or take) in my pocket right now as I wait for the F2 to recharge. Handy way to do routing loads. Very handy, you can snap them open and shut 'with one hand'.

OF

 

[Fat Freddy]

I would like a green Fury 2.

While we're wishing...I'd like a wood grain or marble stone finished Fury!

.

 

[paytonpenn]

No, that's not right. While the flavor will no doubt be spent early on, any THC (etc) you don't consume simply condenses elsewhere in the load. Think about it, nothing is destroyed (no chemical reactions like blazing), the THC doesn't 'leak out', where else could it be by waiting for more heat?

Several guys (and a few women) reported leaving the stem of their PD in the unit OVERNIGHT to find stale taste but more or less full potency next day. I myself performed this experiment. Interrupted sessions on conduction vapes are not fatal. Not to worry.



Are you sure? Mine doesn't, completely. Some still leaks in the charge port if I tape up the intake. Restriction increases, but it still draws. Tape up the charge port too and it's further restricted, but still draws. Then tape up the 3 buttons and it finally is pretty tight........

Or simply blow in the charge port.....what happens? Air 'gushes' out the intake holes? Plug them and it comes out the MP instead?

I don't think it's accurate to say 'it will stop the airflow entirely', at least for the one I have (and now have to peel the tape off of.......

On the topic of what to carry the capsules we don't even have yet I plan to use 'centrifuge tubes', small snap top vials like the one here on the left end of my VM kit (full of herb here):

Amazon carries some sizes, EBay many more. Pointed ones are handy in that you can use the end to pack the load. Hopefully they'll fit the 2cc size:
https://www.amazon.com/Neta-Scienti...=1525658087&sr=1-11&keywords=centrifuge+tubes

If not, I'll be using the fives. I already do this for the FM 'pods', it works well. I also have a 5cc one full of herb (four loads, give or take) in my pocket right now as I wait for the F2 to recharge. Handy way to do routing loads. Very handy, you can snap them open and shut 'with one hand'.

OF

Just whipped out the Fury 2 to check and yeah it stops entirely on my unit. When using the USB port is blown through it's super tight but seems to barely come through the oven area when the top is on not through the mouthpiece or airpath of the oven.

I think I also did multiple airflow checks on my livestream where you can hear my inhales then hear that dead cold stop when the bottom is plugged. I won't doubt other units may be different.

 

[LesPlenty]

Are you sure? Mine doesn't, completely

Mine doesn't either.....until you heat it, probably because I stretched mine a bit by using a Vapexhale elb for a while (I now just use a finer screen in the blue silicon seal)

 

[lookhigh]

Mine is completely sealed on the intake. There is a seal just inside the intake where air leak may occur according to HR. This is not a problem as under normal conditions it is still isolated from the electronics.

 

[mephisto]

@steama that must have been a really bad day for me, I have since seen the error of my judgement. I can fully attest to being a Fury zealot, both for the vape and the customer support. My prior disdain was based (incorrectly) on a full conduction scenario. I drive the Fury every single day, and most folks around me are happy that I do. Cheers!

 

[BabyFacedFinster]

On the topic of what to carry the capsules we don't even have yet I plan to use 'centrifuge tubes', small snap top vials like the one here on the left end of my VM kit (full of herb here):

Amazon carries some sizes, EBay many more. Pointed ones are handy in that you can use the end to pack the load. Hopefully they'll fit the 2cc size:
https://www.amazon.com/Neta-Scienti...=1525658087&sr=1-11&keywords=centrifuge+tubes

If not, I'll be using the fives. I already do this for the FM 'pods', it works well. I also have a 5cc one full of herb (four loads, give or take) in my pocket right now as I wait for the F2 to recharge. Handy way to do routing loads. Very handy, you can snap them open and shut 'with one hand'.

OF

Oh yeah, this is going to be cool. I love those little tubes. That would be so compact and easy for carrying the dosing caps. I hope they fit and if so, how many could one tube hold. I'll need to look up what the "fives" are about.

I want to make a little Fury travel kit and get it down to basic needs for a weekend trip, all in a little tote case. I still need to find the best case to use. I've seen some suggestions here plus I've tried the pelican cases. IDK, the pelicans seem too rigid for what I have in mind.

In addition to the case I'm thinking my kit should include: the Fury 2, usb and wall charger, small brush (I actually like my old Firefly double-sided brush better), small dabber or toothpick, and pre-loaded dosing caps in their own tiny tube.

I would also bring a classic jyarz container and the smoke buddy Jr I just picked up.

I would recommend the smoke buddy for anyone that wants to vape where you need to keep smell to a minimum. IDK if vapor would really set off a hotel smoke alarm but I like the smoke buddy in those cases for peace of mind. Vapor doesn't seem to degrade the charcoal in the SM like with combusting. I've had the same larger buddy for two years now and still going strong. It makes a nice partner to the Fury.

 

[Choices]

While we're wishing...I'd like a wood grain or marble stone finished Fury!

.

https://quantvapor.com/

Hmmm this looks familiar...

 

[OF]

I hope they fit and if so, how many could one tube hold. I'll need to look up what the "fives" are about.

I want to make a little Fury travel kit and get it down to basic needs for a weekend trip, all in a little tote case. I still need to find the best case to use.

Ah, the 'best' case. How do you know there isn't a better one in a different store or web page? A classic logic problem, BTW, fun stuff.

Anyway I'm hoping a single capsule will fit in the smaller tube, if not two should fit the larger size I'm guessing, we'll know when folks try?

Cases can be fun. Consider compact camera hard cases like the VM is in above. Made with rounded corners, and a bit of 'give' in the zipper, they're designed to 'ride well' in a pocket despite being hard. The soft version is also very nice in the correct size, here's the one my MFLB travels in with the contents below:

That, of course, rides even easier. Also there's a host of hard shell cases designed for e-cigs, like here:

That's the small FM (about the same size as F2), cable and charger as you suggest. Also a 'doob tube', another excellent stash container, very vapor tight (dual seals), holds up to a gram of goods, ready to use. Bigger than most pockets, but come in many sizes like the camera cases.

Or not.

Regards,

OF

 

[VapeReady]

Hey,

I'm new here; i might be interested in the Fury 2. Looks like a legit vaporizer. What got my attention is the fact that it's one of the smallest vaporizers... But how would you guys compare it to the Solo II or Mighty performance wise?

 

[Etsu]

Does anyone know if the Crater 420 mini vape is the same as this unit or just a complete knockoff?

Hi all, I was looking for an answer to this, as I live in Europe and can access to the crater unit easier (and a bit cheaper). Looks exactly like the fury 2 but appears to be built with a quartz chamber according to the description. Does anyone know if it’s worth the shot?

 

[OF]

Does anyone know if the Crater 420 mini vape is the same as this unit or just a complete knockoff?

Hi all, I was looking for an answer to this, as I live in Europe and can access to the crater unit easier (and a bit cheaper). Looks exactly like the fury 2 but appears to be built with a quartz chamber according to the description. Does anyone know if it’s worth the shot?

There's a very helpful rep from Fury around here sometimes, I suggest you read back to find one of his posts then send him a PM and asking?

If we all get to guess I notice they also sell a vape that looks like a PaxI so my money's on a knock off.
https://cratervapes.com/vaporizers

Unfortunately.

OF

 

[AtomicPB]

Hi all, I was looking for an answer to this, as I live in Europe and can access to the crater unit easier (and a bit cheaper). Looks exactly like the fury 2 but appears to be built with a quartz chamber according to the description. Does anyone know if it’s worth the shot?

Try vaposhop.com for buying the original Fury2 from within Europe. With the coupon code VAPOBUST2018 you will also receive a 10% discount.

I don't know if it is as cheap as the Crater but it might be worth considering.

 

[sickmanfraud]

I'm new here; i might be interested in the Fury 2. Looks like a legit vaporizer. What got my attention is the fact that it's one of the smallest vaporizers... But how would you guys compare it to the Solo II or Mighty performance wise?

I am not sure a comparison would be fair. A fury 2 is about 1/2 the cost of a Solo II and the mighty is even more expensive.

Try vaposhop.com for buying the original Fury2 from within Europe. With the coupon code VAPOBUST2018 you will also receive a 10% discount.

HealthyRips only charges $5 more for international shipping than USA ($15 vs $10 for USA)

 

[Jill NYC]

Hey,

I'm new here; i might be interested in the Fury 2. Looks like a legit vaporizer. What got my attention is the fact that it's one of the smallest vaporizers... But how would you guys compare it to the Solo II or Mighty performance wise?

The flavor is not as good as Mighty and Solo. And the battery life is much, much less.
But, as someone else mentioned, the price is much less, the portability is clearly in Fury 2’s corner, the heat up time is also much, much faster with the Fury. Also, I think the Fury and Solo are much more efficient with herbs than the Mighty.

 

[VapeReady]

I am not sure a comparison would be fair. A fury 2 is about 1/2 the cost of a Solo II and the mighty is even more expensive.

HealthyRips only charges $5 more for international shipping than USA ($15 vs $10 for USA)

The flavor is not as good as Mighty and Solo. And the battery life is much, much less.
But, as someone else mentioned, the price is much less, the portability is clearly in Fury 2’s corner, the heat up time is also much, much faster with the Fury. Also, I think the Fury and Solo are much more efficient with herbs than the Mighty.

Hmmm this decision is tough i'm hesitating between solo, mighty, or fury 2.

 

[hinglemccringleberry]

The flavor is not as good as Mighty and Solo. And the battery life is much, much less.
But, as someone else mentioned, the price is much less, the portability is clearly in Fury 2’s corner, the heat up time is also much, much faster with the Fury. Also, I think the Fury and Solo are much more efficient with herbs than the Mighty.

This is where I get confused - The Solo is a conduction vape, the F2 is mostly convection. Everyone in the vaping universe talks about how convection gives better flavor than conduction. So how can the F2 flavor not be as good as the Solo?

Also, what is the warranty on the F2? I can't seem to find that info anywhere on their website, or in this thread. I thought I read something on reddit about it being 1 year, with a lifetime 50% off warranty as well. Can someone confirm?