• Do NOT click on any vaporpedia.com links. The domain has been compromised and will attempt to infect your system. See https://fuckcombustion.com/threads/warning-vaporpedia-com-has-been-compromised.54960/.

Divine Tribe atty's

Hi, new DTv3 user. Love this thing, except I'm trying to work out how to get more than one good hit off of it at a time, or is this more of a hit, refill, hit, refill kind of situation? I'm using the "pulse the doughnut, brush on some melted material, take a hit" method, but I'm getting really one really good turn and then I'll need to refill. Is there a way to put more on so I can get a little session going?
 

Danksta

Well-Known Member
Any updates on the crucible cups?

New gear from Source looks pretty good, but I'd rather hold out and keep supporting DT. I really like my V3 but I feel it could be so much better with a crucible cup. I don't use the V3 much anymore.
 

karmakid64

Active Member
Hi, new DTv3 user. Love this thing, except I'm trying to work out how to get more than one good hit off of it at a time, or is this more of a hit, refill, hit, refill kind of situation? I'm using the "pulse the doughnut, brush on some melted material, take a hit" method, but I'm getting really one really good turn and then I'll need to refill. Is there a way to put more on so I can get a little session going?

im a new DT user also experiencing the same thing. I "think" there may be a few temporary factors at play.

I come from using a yocan donut on a tc mod. new donuts vaporized almost the entire dab on the first hit but after a few uses and the donut is "seasoned" and I got two great hits and two not so bad hits I'm supposing it will be the same here.
Also the airflow is amazingly open. getting used to this new draw will probably improve the vape experience as well.:nod:
 

invertedisdead

PHASE3
Manufacturer
Is there another 510 atomizer that the experts recommend that I can use for multiple hits?

IMO It's not even worth hitting concentrate if you are looking for a design like this. You end up huffing on reclaim hits the whole time, it's counter productive. I understand the allure and have tried many other atomizers looking to do the same thing; I'm back to load as you go.
 

Danksta

Well-Known Member
@Danksta what are you using now?

I'm not really using a portable vape atm. I think the V3 is the best tasting portable but it's not easy to work with when out and about. I've found I have to preload it when I leave the house and then finding a safe spot to reload isn't always easy.

I've gone back to smoking out of a sherlock and actually enjoy it.

I think a crucible cup would make the V3 work better. I just want a portable bucket that I can drop dabs in like a banger. Not interested in those portable enails (they all suck). I think the current V3 could work with a plate type atty if they make one. I just hate donuts. They don't cover the whole bottom. They taste great though.

Those firefly pads might be what I want for now. Thanks for pointing those out. Looks like it would create the plate I want. Shame it's SS though.
 

nosmoking

Just so Dab HAppy!
I have a Puffco+, it's been great so far. Incredibly sweet for going out at night, no fuss no muss.
If you take a DTV3 atomizer and remove the donut and cup, you can install a Source Terra 2 heater which is a ceramic crucible with Tungsten wires running throughout so the walls and floor heat and it can be run on TC. Basically its a bigger Puffco Plus.

You can even take a Plus dart and put a layer or two of silicone whip/tube around the black rubber on the dart and push out the splash gaurd on the DTV3 and it will fit in place so you have a dart!
 

karmakid64

Active Member
If you take a DTV3 atomizer and remove the donut and cup, you can install a Source Terra 2 heater which is a ceramic crucible with Tungsten wires running throughout so the walls and floor heat and it can be run on TC. Basically its a bigger Puffco Plus.

You can even take a Plus dart and put a layer or two of silicone whip/tube around the black rubber on the dart and push out the splash gaurd on the DTV3 and it will fit in place so you have a dart!

:tup:awesome! does the DT housing then fit over the terra 2? is there video out on this?
I hope DT puts out something similar
 
If you take a DTV3 atomizer and remove the donut and cup, you can install a Source Terra 2 heater which is a ceramic crucible with Tungsten wires running throughout so the walls and floor heat and it can be run on TC. Basically its a bigger Puffco Plus.

You can even take a Plus dart and put a layer or two of silicone whip/tube around the black rubber on the dart and push out the splash gaurd on the DTV3 and it will fit in place so you have a dart!

Whoa you just blew my mind. Questions if I may?

1. What's your settings for the Puffco + on TC? I have a Pico 75w.
2. What's your all around favorite portable (aside from the Puffco+)?
3. Why did you retire your DTv3? Just curious.

I got the stainless mesh from the Firefly to try in the DCv3. We'll see how that extends the duration.
 
interruptingpirate,
  • Like
Reactions: tennisguru1

aka DaBigKahuna

Well-Known Member
New DTV3 owner here. I have it paired with a Primo Mini. Thank you to invertedisdead for some initial info.

New to AF and have two questions on settings I was hoping for some help with.

- Temp = Would I set at 174 since it looks like it's measured in Celsius which would be 345 Fahrenheit, correct?

- Coil Material = TFR ni or Nickel 200?

So far I:

- Renamed profile
- Set power to 33 watts
- Set mode to TC / enabled PI regulator / Range = 0 / P Value = 1000 / I Value = 20
- Set puff cutoff to 15 seconds

Any other recommendations?

Can't wait to take this for a whirl and I'll post back impressions. Thank you!
 
Last edited:

bizwaxzion

Enigmatic Cannabist
New DTV3 owner here. I have it paired with a Primo Mini. Thank you to invertedisdead for some initial info.

New to AF and have two questions on settings I was hoping for some help with.

- Temp = Would I set at 174 since it looks like it's measured in Celsius which would be 345 Fahrenheit, correct?

- Coil Material = TFR ni or Nickel 200?

So far I:

- Renamed profile
- Set power to 33 watts
- Set mode to TC / enabled PI regulator / Range = 0 / P Value = 1000 / I Value = 20
- Set puff cutoff to 15 seconds

Any other recommendations?

Can't wait to take this for a whirl and I'll post back impressions. Thank you!
DTv3+Primo mini is a great combo. You should be able to set temp units to F in the profile, but it may have been moved to a regional setting in recent builds. I prefer to use TCR for my donuts - 200-230 for 10mm and 450-500 for recent 13mm donuts. For reference Ni TCR is around 600.
 

aka DaBigKahuna

Well-Known Member
DTv3+Primo mini is a great combo. You should be able to set temp units to F in the profile, but it may have been moved to a regional setting in recent builds. I prefer to use TCR for my donuts - 200-230 for 10mm and 450-500 for recent 13mm donuts. For reference Ni TCR is around 600.

Thx biz - is nickel 200 the right coil material drop down?

For TCR do you just need to check or enable Nickel 200?

Can anyone help with switching to Fahrenheit for temperature please? I'm using the latest build 170914. Thank you!
 
aka DaBigKahuna,

invertedisdead

PHASE3
Manufacturer
Thx biz - is nickel 200 the right coil material drop down?

For TCR do you just need to check or enable Nickel 200?

Can anyone help with switching to Fahrenheit for temperature please? I'm using the latest build 170914. Thank you!

Hopefully this helps, I'm still on 170819 but saw this on the NFE forum.

regional settings (Main Menu -> Settings -> Regional): temperature units, time and date format;
 
invertedisdead,

bizwaxzion

Enigmatic Cannabist
Thx biz - is nickel 200 the right coil material drop down?

For TCR do you just need to check or enable Nickel 200?

Can anyone help with switching to Fahrenheit for temperature please? I'm using the latest build 170914. Thank you!
For TCR you choose that option and then supply the number. This number basically represents the delta in resistance per degree (C) - allowing the mod to calculate temperature of the coil from it's actual resistance. I prefer TCR becaue it allows me to change TCR values to get on screen temperature control to show [mostly] acurate values. I do this by measuring actual temperature on the donut with either IR or a thermocouple.
 

aka DaBigKahuna

Well-Known Member
Thank you biz. Do you mind sharing the number you are using now?

What coil material selection is recommended? Thanks all for your patience...

For TCR you choose that option and then supply the number. This number basically represents the delta in resistance per degree (C) - allowing the mod to calculate temperature of the coil from it's actual resistance. I prefer TCR becaue it allows me to change TCR values to get on screen temperature control to show [mostly] acurate values. I do this by measuring actual temperature on the donut with either IR or a thermocouple.
 
Last edited:
aka DaBigKahuna,
Top Bottom