Search results

Nice, that's a lot! Just spotted the 6 x 15 terp pill on the site that I'll add also to the mix ;)

They are pretty pricey and I thought that when I got the showerhead separate awhile ago. I was assuming the 3 hole would be more open, but sure Snacks knows better than me. I've found sharp angle dropdown or extenders adds a little pull vs the smoother ones. Gonna try out some beads as Les...

Sure! You could load just half of the bowl in the half bowl setting for a minimal hit. Dyna style if ya will. Hmm.. maybe. This would be more feasible to avoid an uneven roast but more time each side. Bushranger was moving his back and forth slowly which reminded me of it

Could also get a 18F to 14M adapter so you can switch up the mouthpiece. Works pretty well with a bubbler I have that’s 14 MP.

Yea I’m finding both large & smaller flames working well :tup: I like using a big one with a larger rig, good diffusion, bright glow. Here’s a run with a smaller flame, slight glow, and dry :nod:

Thx, yea that’s the one I’m using which prevents it from sliding through the end and into my mouth. It only falls forward about a thumb’s width until it hits the bottom of the screen, which I can tolerate. It is stuck in there now with some sticky ;)

I’m still running low around 440 with larger/good diffusion rigs and even less with smaller bubblers or dry pieces. 3 small bowls ABV. Super efficient :rockon:

Don’t remember using either w/the 18. Depending on what you like. The inline will have more restriction and better cooling. Need adapter to get it away from face. The mod will be wide open and warmer (9 hole). Not so sure the drop down they sell would clear the top of the rig ..

HERE’S a side by side with TRWW vapes on them without adapters. You’re right, the smaller guy has a joint closer to face with a more upright mouthpiece.

The Vaphit stem working well on this fun day Sunday! Plenty of glass to 🆒 :cool: https://vgoodiez.com/products/dna-glass-stem-by-vaphit

Nah it’s quite oversized and can move around in there. But it sits center and the coil can rest up against the inner porcelain walls no prob. I like to try to get it to balance on there sometimes PIC

Yep this is a great technique and I’m glad you quoted crusty cause I totally spaced that this has an adjustable bowl!! Durp :freak:

That Qaroma cup is nice! I use for the ZX, coil cap, and vulcan bowl. It’s only 5 min, then ready to rip ;) The cool down takes time. My typical ritual is turn on, 3 one snap bowls, turn off :sherlock:

Performing pretty good and getting used to the new feel. I did get the condenser from them with the order last week.

Lol .. got it when I got the tempest but honestly it’s more of a hassle than spinning on rig or by hand 🤟

Few pics of the Dovetail stem that arrived yesterday :rockon:Excellent craftsmanship, lightweight feel, and stays really cool to the touch. The draw is a bit different since the XL condenser isn't long enough to mate up with the bottom of whatever tip you put on. I'm guessing some of the vapor...

HERE’S a side by side pic Red. I wouldn’t say either is superior, just different form factors. Terpcicle is a bit “heftier” with the 3 pieces. QC may be a bit more open with its straight bowl path and balancing heater. Both awesome 😎

Happy Friday y’all. Still having a blast with the Omega. Tried it as a 14mm injector w/glass bowl which worked well! A couple of quick pulls to start the weekend right with the vulcan:rockon:

Sativa snag today :nod: Shop was doing 15% off entire orders for the holiday so grabbed a few.

Timing. Just set your temp and wait at least 5 min after the PID gets to where you set it. If it were a “live” reading, it would go past your setting by roughly 10 degrees, then slowly dip back down, all while the gems are being heated up. Really the only temp that matters is that of the air...